Forum Replies Created
-
Posts
-
Re: A Quandry ?
squadman wrote:
Has Indesit WIL appliances got a inteligence that we have missed !Don’t think so squadman :rotfl:
Re: beko wma 1614w
Did one the other day doing same fault and it was the timer. Have had a few in the past as well – all the same problem.
Martin
Re: Bearings on an AEG washing machine
shaft seal: 50095515008
front bearing: 3790800001
rear bearing: 3790800100
gasket tub shell: 1240159036hth
Martin.Re: Zanussi DE 6754 S diswasher not heating
I had one recently just the same.. re-soldered, changed the relay, all no good. New board fixed it. Must have been the driver transistor to the relay u/s
Re: Supply Point Earth Loop Impedance Testing
Hi Neil,
It looks like you are doing a good job already with earth loop impedance, earth bond and insulation tests.Re: ISE 2
Hi boohoo,
I have an ISE10 1406W myself and i promise you that you will be very impressed with the machine.
I have also installed some, and my customers are absolutely delighted with them.All the best
MartinRe: AEG FAV 44070IM Dishwasher
Hi Toni,
Very likely to be control module, but might just need soldering job on the relay pins.Cheers
MartinRe: Zanussi Drum Paddle
I think the new paddle comes with a screw to fix, which is accessed by removing the sump hose.
Re: Connect Backorders
Same experience with connect here squadman 😥
Backorders that never show up, and then disappear from the backorder list after Months waiting with no explanation.
Emails to them are Never answered.
Emails to Seme & Masterpart are no problem at all.Re: Any feedback on ISE10 models yet?
Hi Garry, I have an ISE10 1400rpm machine myself and can say with absolute confidence that it is a great machine to use.
Its performance is very impressive and gives great results in all respects.
It also does it in half the time that most other machines take, and is a lot quieter than my previous LG machine.Re: Indesit WIDL102 error lights. NTC?
There may also be another component failure in the machine that has caused the board to blow in the first place and if not thoroughly tested may blow a new board instantly! (they blow quicker than a quick blow fuse).
Re: Hotpoint WF541 Error?
Hi Mark.
Looks like the module C00143056 is the correct one so I would think the problem must be with the eeprom.It seems there are a couple of different eeproms to choose from depending on which motor is fitted, and they are not interchangeable!
eeprom part no…
1605639 if FHP motor fitted.
or C00195929 if Ceset motor fitted.Re: Candy (Haier) CS455M dishwasher overheat thermostat
I wonder if it could be the same 78c safety stat that indesit use (part no. C00041086)
Martin
Re: ISE10…
Also Ken, I thought I heard mention at Sibson that the user manual would be a really nice bound folder type thing, but the one that has been included with my machine is not much different to the original ones that came with the ISE5 (black & white photocopied type job).
I would like to say that the wash/rinse/spin performance is absolutely brilliant and the 1400 spin speed is perfectly adequate – and proves (to me) that the program cycles of other machines taking over 2 hours for a 40c wash is just not at all necessary.
Re: ISE10…
Received my First ISE10 today, and a very nice machine it is too.
I hadn’t realised that the spec had changed from what has been previously indicated on the site though ❓
eg..It is a 1400rpm spin machine (not 1600)
It is an AAB rated machine & not AAA.Mine came with a small dent in the front lower panel which I will have to ring David about.
Really like the machine & I think it should sell well.
Can’t wait for the ISE2’s to arrive as I have orders already
😛
