megawatt

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 167 total)
1 2 3 … 10 11 12
  • Author
    Posts
  • August 9, 2012 at 7:57 am in reply to: Hotpoint wma34 manual. #379228
    megawatt
    Participant

    Re: Hotpoint wma34 manual.

    Thanks very much for your help,
    Regards,
    Mike.

    August 6, 2012 at 7:11 pm in reply to: AWM712D. E11 #379027
    megawatt
    Participant

    Re: AWM712D. E11

    Interesting that you had a blocked pump too. Looks like a blocked pump may trigger this pcb fault.
    Mike.

    August 5, 2012 at 9:45 pm in reply to: AWM712D. E11 #379025
    megawatt
    Participant

    Re: AWM712D. E11

    Thanks Ron. Just seen from the fault code list that it is the door lock triac.
    Mike.

    April 29, 2012 at 2:50 pm in reply to: AWCT12L fault codes. #373982
    megawatt
    Participant

    Re: AWCT12L fault codes.

    Thanks for your help Jim. I have sent Martin a PM.
    Regards,
    Mike.

    April 24, 2012 at 8:35 am in reply to: Hotpoint WMA module swap. #373687
    megawatt
    Participant

    Re: Hotpoint WMA module swap.

    Thanks for your reply,the module came from a wma58. Looks like an EMW job,
    Regards,
    Mike.

    March 19, 2012 at 10:22 am in reply to: 1607 wash times. #371312
    megawatt
    Participant

    Re: 1607 wash times.

    Thanks for reply.I Will look in tech info for reset.
    Regards,
    Mike.

    February 23, 2012 at 9:51 pm in reply to: Loud Noise AWCT12L Dispenser fill hose rubbing against tub #369468
    megawatt
    Participant

    Re: Loud Noise AWCT12L Dispenser fill hose rubbing against t

    Well known and talked about on the ISE forum, worth a look.

    February 6, 2012 at 7:06 pm in reply to: Amica AWM612D. E32. #368302
    megawatt
    Participant

    Re: Amica AWM612D. E32.

    Thanks for your response. I don’t know what part of the cycle it came up at. I asked her to give it another try and she has not got back to me yet, so I assume it is ok. No answer on her phone so this is yet to be confirmed. If problem persists I will troubleshoot htr/nct.
    Thanks,
    Mike.

    January 17, 2012 at 9:51 am in reply to: ise 1607 Squeek #367332
    megawatt
    Participant

    Re: ise 1607 Squeek

    Try a bit of grease on the top springs.
    Mike.

    November 11, 2011 at 5:22 pm in reply to: AWCT12 module. #363322
    megawatt
    Participant

    Re: AWCT12 module.

    That’s very good of you Dave. Give me your address and I will get one over.
    Mike.

    November 10, 2011 at 2:17 pm in reply to: AWCT12 module. #363320
    megawatt
    Participant

    Re: AWCT12 module.

    Yea, done that Dave. It is not the diode but something deeper.????
    Mike.

    November 9, 2011 at 7:37 pm in reply to: AWCT12 module. #363318
    megawatt
    Participant

    Re: AWCT12 module.

    I had a look at my dead modules and found my caps ok. I have got a short across D5 but it is not D5 causing the problem.
    Mike.

    November 9, 2011 at 4:44 pm in reply to: AWCT12 module. #363317
    megawatt
    Participant

    Re: AWCT12 module.

    Thanks for the reply Dave. I will have a look at some of my dead ones tomorrow and let you know.
    Mike.

    October 5, 2011 at 3:39 pm in reply to: AWCT10L #358800
    megawatt
    Participant

    Re: AWCT10L

    Had a short in the plug on the pcb that was going to the motor. Worth a sniff.
    Mike.

    September 1, 2011 at 7:46 pm in reply to: AWCT 12L #357161
    megawatt
    Participant

    Re: AWCT 12L

    Machine front top, bot and mid panels come off. Most of the time it is a front tub and concrete blocks change. Give me a ring on 07971 668494 and I will talk you through it
    Mike.

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 167 total)
1 2 3 … 10 11 12