Forum Replies Created
-
Posts
-
Re: BOSCH WTA 2000 DRYER
Start with the red button on the back – does it make a nice solid click when pushed? If it does, you have reset it and should get heat BUT – find the blockage.
Failing that, there is the heater and the thermostat on the back panel, and another thermostat down underneath. Any or all can fail.
Correct use of a multi meter is the only way to diagnose accurately, if you can’t do this, please get pro help. Check Directories or Repairs@ for a UKW engineer in your area.
Power off if investigating yourself.
Regards,
Penguin45.Re: Zanussi Jetstream 1250
Machine employs a carbon brush motor to drive the drum, the brushes may be worn out and need replacing. The “tacho magnet” on the end of the motor may be working loose; this is another common problem. There are other possibilities, but without the model number I can’t be more exact.
Power off before any investigations please. :plug:
Regards,
Penguin45
El Delgado.Re: Bernstein under counter built in freezer seal burst
Some doors have the seal retained by screws, and on some it’s foamed in, requiring a replacement door.
If you would post the model number of your appliance, we should be able to advise further.
Regards,
Penguin45.Re: Creda reversair L – squeaked alot then went cold!!
Lay the machine on its back. Remove small access panel (4 screws). Look in and you will see two arms with wheels at the end – these are the belt tension (or jockey) pulleys. A few drops of oil will usually shut them up. Do not use WD40 or other aerosol lubricants, you will get it on the belt.
Power off, of course.
Regards,
Penguin45.Re: Bosch SGS5002 – Gritty deposits on top rack items
Possibly underfilling, so not enough water being pumped to top rotor is the first thought that comes to mind. Engineers job really – have a look in Directories or Repairs@ to see if there is a UKW engineer in our area.
Regards,
Penguin45.Re: DWF 64SSE TYPE 10045 – Help !
Reset procdure will do no harm if you try it (start button 4 times BTW, not on/off). If the programme appears to select but doesn’t start I’d be more inclined to check the door latch/switch mechanism. The programme cannot start if the door is not shut properly.
Power off of course :plug:
Regards,
Penguin45.Re: WPL Cooker ACM340 857634015000 Regulator
Dave_Conway wrote:
As an aside, does anyone know where I can buy a device that automatically shuts a PC down when alcohol is detected on the breath ? 😆In our house it’s called the Mrs……… 😀
Chris.
Re: Leaking Hoover Nextra Dishwasher
There is an “O” ring seal fitted in the joint of the drain pump housing and the pump motor body. I take it you split this to clear the blockage? If it’s not refitted, the pump will leak.
If you have lost the seal, it is not available from Hoover as a specific spare part – they will only sell the pump complete. However, an “O” ring is an “O” ring, so a visit to a bearing/transmission factors will probably yield what you want.
Regards,
Penguin45.Re: Baucknecht Wash M/c WAE8978 858341312000 Int. Fault
Just been doing a bit more reading – it’s got a flowmeter as part of the inlet set-up, which will also give “HF” if it fails 😕 .
Chris.
Re: Baucknecht Wash M/c WAE8978 858341312000 Int. Fault
The one with the inlet valve at the tap end of the hose……. And a shut-off mechanism in the machine to kill it….. And occasionally a nasty red re-set button, so you have to depressurise the system in order to reset it.
Wonderful things. Not.
Chris.
Re: blomberg upright freezer spec query
Errrrrrrrrrr…… 🙂
Might be a question for Don to answer in the morning. He’s good at these sort of problems.
Cheers,
Penguin45.Re: LG intellowash problems…
Due to manufacturers copyright issues, we are unable to publish the information you require.
However,
http://www.lge.com/support/manual.jsp
should lead you to a replacement manual.Regards,
Penguin45.Re: WMA Drum 5 yr Guarantee
Given that I absolutely detest the blasted things and would be reluctant to stand any sort of warranty on these machines, I always tell the customers about the 5 year warranty.
Cheers,
Chris.Re: smeg DWI710E1
Temperature sensor out of circuit is most likely culprit.
Check in Directories or Repairs@ for a UKW engineer in your area.
Regards,
Penguin45.
