pmb

Forum Replies Created

Viewing 15 posts - 271 through 285 (of 472 total)
1 2 3 … 18 19 20 … 30 31 32
  • Author
    Posts
  • November 5, 2011 at 2:10 pm in reply to: BHWD129 Lights flash #362841
    pmb
    Participant

    Re: BHWD129 Lights flash

    Looked at it today,Bottom lights all flashing, No power to Dryer valve So I assume its the PCB.
    Connect have the PCB but can anyone tell me if it comes programmed.They have 2 listed for this model,Its the one marked
    Triphase

    October 25, 2011 at 1:16 pm in reply to: WIDLX 126UK. Module ? #361481
    pmb
    Participant

    Re: WIDLX 126UK. Module ?

    Sent old Module to EMW but the chip had gone and they couldnt do anything,
    Got new module and sent to EMW for configeration, They only charge £10.

    October 21, 2011 at 1:16 pm in reply to: Miele w304 internal fuse #361685
    pmb
    Participant

    Re: Miele w304 internal fuse

    Thanks alot Seamy thats great, i missed that when i was searching this problem 😀

    October 12, 2011 at 3:52 pm in reply to: Indesit Model Number #361268
    pmb
    Participant

    Re: Indesit Model Number

    Thanks,
    I have not got one in stock, So it would have been a wasted journey.

    October 6, 2011 at 8:13 am in reply to: Whirlpool W/D, no power to valve #360676
    pmb
    Participant

    Re: Whirlpool W/D, no power to valve

    Yes valve is OK,But no live to valve.
    So it most be the Module.

    September 23, 2011 at 3:54 pm in reply to: Check your connect invoices! #358396
    pmb
    Participant

    Re: Check your connect invoices!

    Just checked my order from Masterpart,
    5x 1860H7 belts, Charged me £3.31 each,
    Should have been £1.79
    I will start photocopying order when i put order in.

    September 18, 2011 at 5:05 pm in reply to: Panasonic NA14VA1 #358957
    pmb
    Participant

    Re: Panasonic NA14VA1

    found a easy way to fit.Remove weight above gasket,
    Band has loops just before spring, put plastic tie through loops
    tighten until closes up and clip together.

    September 13, 2011 at 5:14 pm in reply to: Panasonic NA14VA1 #358956
    pmb
    Participant

    Re: Panasonic NA14VA1

    Thanks but their is a small tear, Not sure if it was caused by
    spring or not, I can repair it with silicon.

    August 30, 2011 at 4:27 pm in reply to: ZWD12270W1 Dead #357914
    pmb
    Participant

    Re: ZWD12270W1 Dead

    Thanks Criscold.
    They have decided to buy a new Machine, I am happy with that

    July 27, 2011 at 5:39 pm in reply to: ZWD16270WI Not Starting #356249
    pmb
    Participant

    Re: ZWD16270WI Not Starting

    There is no module in base.
    They wont it done very quickly, So i advised them to call Zanussi, And of course i didnt charge them.

    July 26, 2011 at 3:45 pm in reply to: ZWD16270WI Not Starting #356246
    pmb
    Participant

    Re: ZWD16270WI Not Starting

    Disconnected Dryer heater= still faulty.
    Whats the inverter board, it it the one with the relays on
    Part number 1324478021

    July 20, 2011 at 4:55 pm in reply to: Meile rinse light flashes #355866
    pmb
    Participant

    Re: Meile rinse light flashes

    Thanks
    This customer wonts it done quickly and changing relays on PCB
    is not something i would wont to do,
    Told customer to find a Meile Specialist.

    April 27, 2011 at 9:32 pm in reply to: Luxor WM spares #350196
    pmb
    Participant

    Re: Luxor WM spares

    Thanks alot Don thats really helpful, i will give them a call in the morning 🙂

    April 22, 2011 at 7:54 am in reply to: Bosch dw with detergent in salt container #349855
    pmb
    Participant

    Re: Bosch dw with detergent in salt container

    Thanks alot wizard thats great, i will do that tomorrow 🙂

    April 7, 2011 at 1:28 pm in reply to: LG WM16115FD dispenser leaking #348545
    pmb
    Participant

    Re: LG WM16115FD dispenser leaking

    Hi thanks for getting back to me, i haven’t actually seen it leak even though i have watched it fill in all positions. I went back to see what i could do and typically it was fine, my customer has used it since and no leaks so we will see. Cheers Peter

  • Author
    Posts
Viewing 15 posts - 271 through 285 (of 472 total)
1 2 3 … 18 19 20 … 30 31 32