pup

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 464 total)
1 2 3 4 5 … 29 30 31
  • Author
    Posts
  • July 29, 2010 at 9:15 am in reply to: diplomat dw,hja8630 #326402
    pup
    Participant

    Re: diplomat dw,hja8630

    then u need a megger , otherwise how u going to sort it? 😥

    July 29, 2010 at 7:16 am in reply to: diplomat dw,hja8630 #326400
    pup
    Participant

    Re: diplomat dw,hja8630

    well only to do is disconnect heater ? 😆

    July 28, 2010 at 2:42 pm in reply to: Zannusi W/Dry ZWD16270W – C24 Fault code #326353
    pup
    Participant

    Re: Zannusi W/Dry ZWD16270W – C24 Fault code

    first try dryer heater disconnect all wires ,had one last week doing same it was td heater 😆

    July 27, 2010 at 8:17 am in reply to: Kenwood Kdw 243 wash motor #326094
    pup
    Participant

    Re: Kenwood Kdw 243 wash motor

    u get hose clips from halfords 😆

    July 27, 2010 at 8:11 am in reply to: Boy dies in Tumble Dryer horror #326257
    pup
    Participant

    Re: Boy dies in Tumble Dryer horror

    Surley in this day and age one can come up with door lock or something ?

    July 22, 2010 at 1:06 pm in reply to: aeg w/dryerl16830 enr 914602122 #325826
    pup
    Participant

    Re: aeg w/dryerl16830 enr 914602122

    adv wrote:what are amp tags by the way?

    well 🙁 🙁

    July 22, 2010 at 1:02 pm in reply to: samsung side by side rs21dgrs1 #325978
    pup
    Participant

    Re: samsung side by side rs21dgrs1

    check sensor

    June 29, 2010 at 8:49 pm in reply to: Domestic and General cutting agents #324116
    pup
    Participant

    washdoctor wrote:

    appleelectrics wrote:
    had a meeting with them today, apparantly they are looking to cut up to a third of the independants and pass work on to the manufactures !!!

    Meeting with who? I read that as you mean D&G? Needs clarifiying if it wasn’t them you spoke with to stop rumour and prevent Dan76 worrying about a life on crack 😆

    Adrian 🙂

    dont worrying about dan76 i am thinking of those poor sheep 😆

    June 29, 2010 at 8:27 pm in reply to: work dead #372381
    pup
    Participant

    Re: work dead

    wards wrote:well i,m sitting here reading posts,says something about the work situation,got away for a long weekend last friday and came back yesterday,may aswell have made a week of it 8)

    hi it always slow around here mate 😆

    June 12, 2010 at 11:21 am in reply to: Fridgemaster MTRL130 #111866
    pup
    Participant

    Re: Fridgemaster MTRL130

    technics1200 wrote:Cheers!

    You guys are soooo much help!
    Gonna get VT9 out of car now to try it…..

    😆 😆 😉hi 😆

    May 20, 2010 at 4:59 am in reply to: De Dietrich D/W VZ9996U1/1 #320658
    pup
    Participant

    Re: De Dietrich D/W VZ9996U1/1

    is there feed to vavles ?

    May 19, 2010 at 2:00 pm in reply to: Reasons not to DIY (or let your friends repair)… #320635
    pup
    Participant

    Re: Reasons not to DIY (or let your friends repair)…

    iadom wrote:So what was the complaint they called you out for. 😆

    no heat 😆

    May 6, 2010 at 2:24 pm in reply to: Hotpoint FF92 Frost Free “P1” Error #319151
    pup
    Participant

    Re: Hotpoint FF92 Frost Free “P1” Error

    thanks jim 😆

    May 6, 2010 at 2:16 pm in reply to: HEC 12ESM Dishwasher #319513
    pup
    Participant

    Re: HEC 12ESM Dishwasher

    could be float s//w

    May 6, 2010 at 11:23 am in reply to: Hotpoint FF92 Frost Free “P1” Error #319149
    pup
    Participant

    Re: Hotpoint FF92 Frost Free “P1” Error

    Hi jim hope you ok ,can you pls send me one as well ta i got one which is right pig haveing chanege both sensor and fan motor fridge is not holding temp goes too hot say 20 plus and then back to 3/4 have clean and check cooling fan check that flap thingg in firdge

  • Author
    Posts
Viewing 15 posts - 46 through 60 (of 464 total)
1 2 3 4 5 … 29 30 31