repman

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 127 total)
1 2 3 … 7 8 9
  • Author
    Posts
  • August 8, 2013 at 7:29 pm in reply to: Bosch Classixx SGS43C12GB NOT FILLING #398853
    repman
    Participant

    Re: Bosch Classixx SGS43C12GB NOT FILLING

    If pump runs when the door is open the safety system is active that is the mushroom in the base of the tub next to the filter ,either there is water leakage in the very bottom or float is jammed in the upper position for some reason.
    Jim

    January 28, 2013 at 11:46 pm in reply to: Bosch HM48141 Oven Tripping Out with Grill #388889
    repman
    Participant

    Re: Bosch HM48141 Oven Tripping Out with Grill

    Hi the part number is 495410 you should be able to get it from the store on this site

    Jim

    January 28, 2013 at 8:45 pm in reply to: Bosch HM48141 Oven Tripping Out with Grill #388887
    repman
    Participant

    Re: Bosch HM48141 Oven Tripping Out with Grill

    Looks like a duff model number You need to find the E number on the frame when the door is opened

    Jim

    January 28, 2013 at 8:28 pm in reply to: Electrolux EOB5630X cut out #388670
    repman
    Participant

    Re: Electrolux EOB5630X cut out

    Thinks its the cooling fan controller ,it should be called a cut IN!

    Jim

    January 28, 2013 at 8:23 pm in reply to: Hotpoint BW61 Washer Dryer Filling with cold water #388743
    repman
    Participant

    Re: Hotpoint BW61 Washer Dryer Filling with cold water

    Out of interest do you have low hot water pressure? as this tends to cause the valve to pass although you will need to change it , you can then use a “Y” piece and couple the hot inlet to the higher pressure cold water.

    Jim

    January 24, 2013 at 7:00 pm in reply to: Electrolux EOB5630X cut out #388666
    repman
    Participant

    Re: Electrolux EOB5630X cut out

    [quoteDo you think its a dodgy part?]

    Yes unless wiring is muxed up

    Jim

    January 22, 2013 at 7:43 pm in reply to: Hotpoint WMA32 #388428
    repman
    Participant

    Re: Hotpoint WMA32

    The component that has failed is a surface mount triac and is destroyed by a faulty interlock.I hade tried to repair many these boards with very poor results as most times there are other component that have also been damaged

    Jim

    January 15, 2013 at 5:33 pm in reply to: Ariston oven DOV371B TOC #387880
    repman
    Participant

    Re: Ariston oven DOV371B TOC

    MER156975 is the number from connects number

    Jim

    January 11, 2013 at 8:45 pm in reply to: Bosch WAE24469GB/14 Door seal 2 in 3 years #387637
    repman
    Participant

    Re: Bosch WAE24469GB/14 Door seal 2 in 3 years

    Does she use any kind of creams or oils, does any family member have eczema?


    I have a customer with a five year old Bosch and have changed the seal as many times for the same reason .

    Jim

    January 11, 2013 at 8:31 am in reply to: Zanussi ZDC47100w Condenser Dryer cuts out! #387356
    repman
    Participant

    Re: Zanussi ZDC47100w Condenser Dryer cuts out!

    part no 3792171112 sounds like yours is not well
    should be 20deg-6k,60deg-1.2k,80deg 0.64k

    use the link below for parts

    http://shop.ukwhitegoods.co.uk/contact_us.php

    jim

    January 9, 2013 at 8:34 am in reply to: Hotpoint WD440P – no heat #387020
    repman
    Participant

    Re: Hotpoint WD440P – no heat

    or even a broken wire

    jim

    January 9, 2013 at 8:31 am in reply to: Statesmen washer #387545
    repman
    Participant

    Re: Statesmen washer

    sure just phone em up
    08448485862

    jim

    January 8, 2013 at 10:08 pm in reply to: Electrolux EOB5630X Fan problem #387513
    repman
    Participant

    Re: Electrolux EOB5630X Fan problem

    Is it strange that the fan works after the oven gets hot?

    No as its a bearing fault on the motor they usually free up with heat

    Jim

    January 8, 2013 at 9:29 pm in reply to: Electrolux EOB5630X Fan problem #387511
    repman
    Participant

    Re: Electrolux EOB5630X Fan problem

    You need to renew the fan motor .This is a common problem.

    Jim

    January 8, 2013 at 7:37 pm in reply to: Zanussi F1245W #387493
    repman
    Participant

    Re: Zanussi F1245W

    definitely worth a try-check/change the cap on the timer ,Think 1.5 uf .

    Jim

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 127 total)
1 2 3 … 7 8 9