Forum Replies Created
-
AuthorPosts
-
repman
ParticipantRe: Leisure Naples np10frs not getting hot
Probably the fan element has failed
jim
repman
ParticipantRe: smeg DI612CA1 goes pop
any dead mouse?
repman
ParticipantRe: whirlpool w/m inlet valve
481928128223 from connect but says obsolete
jim
repman
ParticipantRe: BOSCH Logixx 8 spin cycle sometimes – imbalance?
good,and the plastic tag is the door release if pulled down
jim
November 22, 2012 at 9:22 am in reply to: Stoves Cooker Cuts Out After About 1.5hrs See Photos #385168repman
ParticipantRe: Stoves Cooker Cuts Out After About 1.5hrs See Photos
part no is STV082814400
jim
November 21, 2012 at 9:29 pm in reply to: Stoves Cooker Cuts Out After About 1.5hrs See Photos #385167repman
ParticipantRe: Stoves Cooker Cuts Out After About 1.5hrs See Photos
yes that is the board marked and i can get part number 4 you tomorrow but the cap is a awful lot cheaper but its up to you
jimrepman
ParticipantRe: Matsui MF2W/A dishwasher stuck cycle
think you may have to lay the m/c on its back and remove base to see
repman
ParticipantRe: Matsui MF2W/A dishwasher stuck cycle
I seem to remember a d/w it was midea and it had a thermostat and a thermal fuse elsewhere on the base.They both look the same so its best to chase the wiring to find it.
November 21, 2012 at 6:43 pm in reply to: Fitting 4 Tag Solid Plate – Replace 2 Tag Type? See Photo #385161repman
ParticipantRe: Fitting 4 Tag Solid Plate – Replace 2 Tag Type? See Phot
1-2———–supply
3-4———–supplyNovember 21, 2012 at 6:14 pm in reply to: Stoves Cooker Cuts Out After About 1.5hrs See Photos #385165repman
ParticipantRe: Stoves Cooker Cuts Out After About 1.5hrs See Photos
unit operates as follows-oven or grill switch feeds the fan control board after a short delay the fan is powered by the board via the resistor then continues until oven and grill turned off and the FIXED delay has expired,the common faults we have found for no fan run are resistor open circuit (its in there to reduce the power of the fan) or fan board fault which seems to always be the capacitor,
jim
repman
ParticipantRe: electrolux ew1200i
sounds like a new timer then!
jimrepman
ParticipantRe: Is this a configuration problem ?
922CB02A1507F9CF IS THE CONFIG CODE
MODULE,NO 132 12 25-63/1 IS NOT CONFIGUREDrepman
ParticipantRe: electrolux ew1200i
hi if the spin appears to speed up then slow down many times before switching off you probably do need a new timer
jim
ps
i have assumed the filter is clear.repman
ParticipantRe: Whirlpool oven AKP20http://www.whirlpoo7/1X flashing – –
Door lock :
1. With knobs (1) and (5) set to “0”, press buttons “ok” and – at the same time for 3 sec. The indicator next to the symbol lights up.
2. The oven functions will not operate while the door lock is activated.
3. To deactivate the lock, repeat the sequence described in point 1repman
ParticipantRe: Zan auto zwf1432s
check for damage on the main board,if you find any you will need to chase down what caused it
-
AuthorPosts
