RickT

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 198 total)
1 2 3 … 7 8 9 … 12 13 14
  • Author
    Posts
  • July 9, 2010 at 9:25 pm in reply to: Zanussi ZWF12070W #325048
    RickT
    Participant

    Re: Zanussi ZWF12070W

    You can view diagnostics and fault codes on Connects mediator. Under Service manual click view in pdf.
    Hope that helps.

    July 8, 2010 at 3:52 pm in reply to: Join DASA for just £65 #324917
    RickT
    Participant

    Re: Join DASA for just £65

    Same here. In the recycle bin, of course 😉

    June 28, 2010 at 6:36 pm in reply to: Bosch WFLI2440GB overfilling #324056
    RickT
    Participant

    Re: Bosch WFLI2440GB overfilling

    Assuming that the water level is rising during this period of intermittent filling and not syphoning away, I would suspect pcb!

    June 28, 2010 at 8:34 am in reply to: Bosch WFLI2440GB overfilling #324052
    RickT
    Participant

    Re: Bosch WFLI2440GB overfilling

    Have you tried blowing into the pressure switch via the tube, plugging the tube and waiting for the click?

    June 19, 2010 at 1:58 pm in reply to: Indesit WIL103uk #323290
    RickT
    Participant

    Re: Indesit WIL103uk

    Thanks for the reply. Customer has since told me that the machine would occasionally turn on when not in use. So it’s definitely the pcb. Thanks again.

    June 18, 2010 at 8:46 pm in reply to: Connect vt9 stats #323042
    RickT
    Participant

    Re: Connect vt9 stats

    I’ve had loads, shafts loose, binned them all. If you order FRG6600, they’re ‘Ranco’ and have a much more possitive switching.

    June 18, 2010 at 5:25 pm in reply to: Connect Prices #288107
    RickT
    Participant

    Re: Connect Prices

    Hotpoint wm laminated brushes retail prices
    Hotpoint website £19.99
    Connect £24.51
    4hotpoint.co.uk(connect retail)£8.99 ????????????

    January 27, 2010 at 6:43 pm in reply to: Hotpoint dryer CTD80 wiring diagram #310338
    RickT
    Participant

    Re: Hotpoint dryer CTD80 wiring diagram

    Possible heater relay or dry joint on module down on the right hand side.

    January 8, 2010 at 8:59 am in reply to: Indesit WM12XUK chassis repair #308155
    RickT
    Participant

    Re: Indesit WM12XUK chassis repair

    Thanks, I’ll give that a try. 🙂

    January 7, 2010 at 6:41 pm in reply to: Indesit WM12XUK chassis repair #308152
    RickT
    Participant

    Re: Indesit WM12XUK chassis repair

    Thanks for the reply. I might just order the kit as there doesn’t look like any alternative, apart from a welding job. The dampers look the same as usual. It’s just whether there’s the space on the chassis for the plates. What does the kit actually comprise of ?

    January 4, 2010 at 9:21 pm in reply to: HOTPOINT WF430 #307833
    RickT
    Participant

    Re: HOTPOINT WF430

    Had this a little while back. Front display board faulty.

    November 12, 2009 at 9:42 pm in reply to: Zanussi FJ1254 sticks on wash #303536
    RickT
    Participant

    Re: Zanussi FJ1254 sticks on wash

    Yes, checked it first and after fault occured no problem there. Wondered if the pcb relay could be breaking down after a while. Haven’t visually checked this yet!

    October 31, 2009 at 4:09 pm in reply to: Any one got a clue? #302228
    RickT
    Participant

    Re: Any one got a clue?

    Unfortunately I am 🙁

    October 31, 2009 at 3:49 pm in reply to: Any one got a clue? #302225
    RickT
    Participant

    Re: Any one got a clue?

    Some type of tripod? Perhaps a clothes dryer/hanger

    October 27, 2009 at 8:04 pm in reply to: Bosch dishwasher SGS5302GB/07 #300573
    RickT
    Participant

    Re: Bosch dishwasher SGS5302GB/07

    Just the job.
    Many thanks Alan

  • Author
    Posts
Viewing 15 posts - 106 through 120 (of 198 total)
1 2 3 … 7 8 9 … 12 13 14