robbra

Forum Replies Created

Viewing 15 posts - 346 through 360 (of 1,090 total)
1 2 3 … 23 24 25 … 71 72 73
  • Author
    Posts
  • November 18, 2010 at 4:10 pm in reply to: For the attn. of the Hotpoint genii #336331
    robbra
    Participant

    Re: For the attn. of the Hotpoint genii

    Jim
    It’s inside the tube on the switch. At first I thought it was a blockage.

    November 18, 2010 at 8:15 am in reply to: WTA Logo #229165
    robbra
    Participant

    Re: WTA Logo

    Thanks Ade,
    Will ask my signwriter to make a couple of copies for the van.
    Maybe as a few more members since Amica came on there might be a bit more demand
    Rob

    November 18, 2010 at 7:00 am in reply to: Connect Prices #288115
    robbra
    Participant

    Re: Connect Prices

    I have sent badly burnt modules to EMW and no problems. Give them a ring.
    Rob

    November 17, 2010 at 6:06 pm in reply to: Connect Prices #288111
    robbra
    Participant

    Re: Connect Prices

    mines £229.01 + vat. so even worse.
    Is there a problem sending the module to EMW?
    Rob
    I’m doing a lot with Qualtex lately and happy with them.

    November 17, 2010 at 2:57 pm in reply to: WTA Logo #229163
    robbra
    Participant

    Re: WTA Logo

    Are there any van stickers available?
    Rob

    November 16, 2010 at 4:05 pm in reply to: Whats the most annoying thing customers do? #107813
    robbra
    Participant

    Re: Whats the most annoying thing customers do?

    Allsorts wrote:I would have been asking her who the bloke was 😀

    Martin is the only one who has been there :eeek: :eeek:

    Only jesting friend.
    Rob

    November 16, 2010 at 9:42 am in reply to: Askoll drain pump rotor swapping. #335995
    robbra
    Participant

    Re: Askoll drain pump rotor swapping.

    Martin,
    you are one saucy s*d 😆

    November 16, 2010 at 8:10 am in reply to: Askoll drain pump rotor swapping. #335992
    robbra
    Participant

    Re: Askoll drain pump rotor swapping.

    I would not do it as the hole at the back of the housing that takes the shaft can wear out of shape and reduce the life of the pump and resulting in a recall but you’ll need some pumps sooner or later so go ahead and spend some of the money you don’t pay on road tax and your tv licence 😆
    Rob

    November 16, 2010 at 8:06 am in reply to: Servis M6852 W #335982
    robbra
    Participant

    Re: Servis M6852 W

    Steve,
    sometimes the selector can play up (I have taken them apart and cleaned them too) but in with this scenario I always say to the customer switch off, select off, switch on for 10 secs, switch off, select programme and switch on then start. I know it’s long winded but as these boards can memorise previous programmes it normally clears it.
    HTH
    Rob

    November 16, 2010 at 7:22 am in reply to: Baumatic BDW13/ Indesit clone #335874
    robbra
    Participant

    Re: Baumatic BDW13/ Indesit clone

    I don’t know where you found that but it’s identical at less than 1/3rd the price.Let me know
    Thanks
    Rob

    November 15, 2010 at 4:31 pm in reply to: Baumatic BDW13/ Indesit clone #335872
    robbra
    Participant

    Re: Baumatic BDW13/ Indesit clone

    Thanks,
    Tried them but not much help and more expensive than CDSL
    Rob

    November 12, 2010 at 7:02 pm in reply to: Hotpoint WF440 #335649
    robbra
    Participant

    Re: Hotpoint WF440

    Blooming long creep is all I can say, around 350 miles.
    I’m H A P P Y
    unless she ‘phones me soon :eeek:

    November 12, 2010 at 3:54 pm in reply to: Angled ratchet spanner. #335748
    robbra
    Participant

    Re: Angled ratchet spanner.

    King Dick 3/8th for me but the only thing I ever use a 1/2 inch on is……….Wheel nuts 😆

    November 12, 2010 at 2:40 pm in reply to: Angled ratchet spanner. #335746
    robbra
    Participant

    Re: Angled ratchet spanner.

    That looks good for those Hotpoint and Bosch motor bolts but it’s 1/2 inch not 3/8th.
    Will have a look next week.
    Rob

    November 12, 2010 at 2:36 pm in reply to: Hotpoint WF440 #335646
    robbra
    Participant

    Re: Hotpoint WF440

    Thanks for all the help but can anyone explain why, when I went back this morning before touching it I turned it on and the bu**er started spinning.
    I was so relieved so will get a malt later and toast WF440. Nah I’ll curse them
    PHEW!!!
    Rob

  • Author
    Posts
Viewing 15 posts - 346 through 360 (of 1,090 total)
1 2 3 … 23 24 25 … 71 72 73