[RocketMan]

Re: INDESIT WD1230G SRL 912028003

Thanks aqualectric, your were right, turned out to be blown track, five minute with a soldering iron – Bobs your uncle…

Model turned out to be WG1230G UK.

One happy customer and one happy engineer –

Thanks to all for the help.

RM 😀 😀 😀 😀

[RocketMan]

Re: INDESIT WD1230G SRL 912028003

Thanks guys, looks like I’ll have to go and double check model and look at it.. help much appreciated.

Thanks

RM 🙂 😀

[RocketMan]

Re: INDESIT WD1230G SRL 912028003

Sorry, got details from the customer, probably a W1230G ??
RM 😕 😕

[RocketMan]

Re: Hotpoint CTD00 condensor dryer

1703080 – shaft kit ver 4. You’re right. the pads now replace the 2 white wheels. (pullies)
When fitting the bearing pads do not fit one to the top left of the air duct/front drum support (when viewed from the back) modification number 999 to try and get them to work!!!!!! 😯 😯

However, if at all possible, try turning the pullies around… done this a few times….seems to have worked..

check shaft has not snapped or shaft has not been torn from back of drum…both common.

Also, might just need a couple of m8 washers between shaft and back of drier (modification number 327…….))

Also these MUST be on completely level and even surface!!

If a very early version might need all modifications ….

Best of luck. you need it.

RM 😉

[RocketMan]

Re: BOSC WFB2005FG/31 FD7805 01635

Thanks for that, will order both but the fascia @ nearly £74.00… bit steep…, have to get D & G to auth the repair… thanks to all for the help.

RM 🙂 🙂 🙂 🙂

[RocketMan]

Re: Hoover drum lifters

I’ve done it before on different models. Access the screw via the sump, remove the screw you can access and then very gently (from in the the tub), break up the lifter. Bear in mind there may still be another screw holding it in. You’ve got to be really careful not to damage the drum.
Fit the new lifter and put one screw in via the sump again. Not sure if it is the same for this model but this is easier than the drum out scenaria.

Regards
RM
😉 😉 😉

[RocketMan]

Re: Bosch Condensor dryer – WTL6106GB probem

Hi, Got the full Bosc manual on this if you want it… PM if you want a copy…
1.3MB though, hope u got broadband. 🙂 🙂 🙂 🙂

RM

[RocketMan]

Re: Zanussi EC ZCE7600 PNC 948522006 – ((serial z7e44100017

Thanks guys, appreciate that. Will give the customer the price and see if he wants the cooker repairing.

RM 🙂

[RocketMan]

Re: Known Error Codes

Baumatic Dishwasher Error Codes

E1 Longer Fill Time – low presure/supply tunred off/faulty valve
E2 Longer or extended draining time….
E3 Longer heating time – NTC/Element fault
E4 Overfilled (water in base) …be carefull these over fill for many reasons including using 3-1 and salt according to the manual ??????
E5 Cannot switch off automatically – programme not finishing (not for BDW 13, 14 or 15)
E6 OC Thermister
E7 SC Thermister

Hope these can be helpful

Steve

[RocketMan]

Re: Baumatic DW – BDW13

I’m sure it’s E3 as there was not water in the base. It just times out on the heating but does heat very slowly. I’ll let you know when I go back.

Steve

[RocketMan]

Re: Baumatic DW – BDW13

eastlmark

Thanks for that – the Smeg codes do look good I’ll check thermister

Steve 😕

[RocketMan]

Re: Indesit TD87 MK2 Vented TD – serial 8902m 9904

Thanks for that Dave.

Steve 😀

[Author]

Posts