Forum Replies Created
-
Posts
-
Re: Hotpoint WF745A 44182525 Tub/Bearing
you cant use the welded drum cos the sump hose fits to front of tub for a pump with filter at front bottom right.
Re: all hotpoints/ wt965a
change board if motor harness ok, i would fit a harness even if no break visable first, before board.
Re: Question for Indesit employed engineer?
i would fix it on the condition it was moved before further use, if they would not move it i would fix it and charge the buggers 😆 thats cos im a franchise not employed .
Re: WMA 30 prewash light flashing
it will be pressure chamber or sump hose blocked, prewash light flash means its timed out on somthing, usually draining.. hope this helps
Re: wma tub
wma rear halfs are still available, but i used to do about 8 to 10 a week for them now only average 2 a week, bearing replacement is being encouraged and i recieved the tool last week, moulded tubs are gonna be the way forward, the new aqualtis 7.5 kg machine has a moulded tub. bearings are easy to do without tool, bash them out knock them in with a bit more care. i think they are looking at monthly fitting of rear drums to see if it warrants suppling us with more expensive tub rear ..
Re: Hotpoint CTD80 condensing tumble dryer
just had another look on partfinder, there is a red tec bulletin on this dryer , if a heater vwith 2 stats fitted on appliance it must be replaced with a heater kit 1703245 from ser no 507120001 to 511299999 (29/11/2005) or a 1703595 from ser 511300001 (30/11/2005) to date. heater kit comes with stats fitted. hopes this makes sense. thing is if stats are ok that cust fitted it will still be module needed.
Re: hotpoint intergrated bwd 20…wont drain
its made by smeg, if the pump runs it must be a sock or something in sump hose, take off at tub end and have a look. there is no ball in sump on this model, it has a flap valve set up going by manuel.
Re: Hotpoint CTD80 condensing tumble dryer
sorry got that wrong from dc 507120000 jul 05 the cycling stat was removed . 😳
Re: Hotpoint CTD80 condensing tumble dryer
before date code 50712 which yours is the heater only has 2 stats one shot and cycling, after dc 50712 they used 3 stats. by the sound of it you will need to fit a module and eeprom. one thing though check condenser these block within about 2 weeks on this piece of sh, sorry i mean this little baby 😆 let me know if need any more info as i franchise for hotpoint, got up to date partfinder.
Re: Creda T602CW Dryer
if it has a module fixed in top rhs looking from front, replace that as it is a sensing module, check that the earthing brush is making contact or not broken. check that condenser is clear, also check that no build up of lint between door panel behind lint filter.. hope this helps .
Re: miele dishwasher g673 all lights flash
you switch on hear a relay click try to select a prog and all 5 led just light.
Re: hotpoint TDC62G killing toc’s…
make sure customer is not taking load out before cycle finished, this also kills stats as no cool down period is alowed.. obvious i know but these women all do it :rolls:
Re: Hotpoint WF860P
check the motor plug pull on wires as sometimes they break in plug, had this quite often
Re: Hotpoint CTD40 condenser drier.
noise is that it needs conversion from wheels to bearing pads on front ducting, heat problem is prob module and eeprom, if stats have been fitted, i fit complete heater kit as it comes with stats. the early ones of these are poor, slightly better now though. :rolls:
Re: Faulty Hotpoint Lam Brushes
ive not had any translucent ones through for ages , i get the white lam ones through, im franchise for them so parts come direct, there probably trying to get rid of the old stock to suppliers. ive been getting used modules through in new boxes so watch out for that one!!
