Simon46

Forum Replies Created

Viewing 15 posts - 1,861 through 1,875 (of 2,216 total)
  • Author
    Posts
  • in reply to: Hoover H160l Inter@act 1600 – error 5 #148113
    Simon46
    Participant

    Re: Hoover H160l Inter@act 1600 – error 5

    This will need diagnosing by an engineer. Looks like a fault in the heating circuit. Check out Repairs@ on LHS of page. Unplug power if you are going to have a look yourself :zap:

    Regards
    Simon.

    in reply to: WMA 20P replacement Drum /bearings #148043
    Simon46
    Participant

    Re: WMA 20P replacement Drum /bearings

    Thanks Tony.
    Here goes!

    S. 🙂

    in reply to: Smeg DWI 1612C program button #147886
    Simon46
    Participant

    Re: Smeg DWI 1612C program button

    Dave can i order it from you? If so how long would it take and cost?

    Regards
    S.

    in reply to: hotpoint dwf element clamp tool? #147705
    Simon46
    Participant

    Re: hotpoint dwf element clamp tool?

    Check out http://www.zeroclips.com/tridon_page5.htm
    Or you can contact Steve Lewis on 0121 622 3211. I found a 31-51 mm (350-024) and also an 18-38mm (350-016) cone in handy. Think he said min order a tenner.

    Regards
    Simon.

    in reply to: Indesit WA155 f10: unsure of fault diagnosis #147141
    Simon46
    Participant

    Re: Indesit WA155 f10: unsure of fault diagnosis

    Andy have not heard from customer so assuming o.k. Did not remove module so either thermistor contact or P/sw. 😕

    S.

    in reply to: NEF B1421 OVEN #147592
    Simon46
    Participant

    Re: NEF B1421 OVEN

    Sounds like worn hinges and or receivers.

    Regards
    Simon.

    in reply to: Stoves EL916 fan oven element #147388
    Simon46
    Participant

    Re: Stoves EL916 fan oven element

    Ahh ELE101.

    S.

    in reply to: Stoves EL916 fan oven element #147387
    Simon46
    Participant

    Re: Stoves EL916 fan oven element

    Thanks Dave. Want to avoid caremark as the last element took 5 weeks to arrive, went distorted and fouled the fan after a week and had to buy another and wait 4 months for refund. Will check oven for number.

    S.

    in reply to: Servis M6011 belt size? #147357
    Simon46
    Participant

    Re: Servis M6011 belt size?

    😀
    Thanks to all.

    S.

    in reply to: Servis M6011 belt size? #147355
    Simon46
    Participant

    Re: Servis M6011 belt size?

    Would qualtex POL 75 1220J5EL fit?

    S.

    in reply to: bosch dryer 3204gb #147206
    Simon46
    Participant

    Re: bosch dryer 3204gb

    Does it work o.k on 30 minute cycle?

    S.

    in reply to: Problem with Bosch – not taking in water #147184
    Simon46
    Participant

    Re: Problem with Bosch – not taking in water

    Does it run on the quick wash?

    Regards
    Simon.

    in reply to: bosch dryer 3204gb #147203
    Simon46
    Participant

    Re: bosch dryer 3204gb

    Is this the one with the carbon brush which wears out on the drum?

    in reply to: Indesit WA155 f10: unsure of fault diagnosis #147139
    Simon46
    Participant

    Re: Indesit WA155 f10: unsure of fault diagnosis

    AHH
    Opened pressure switch.
    Sh**ty alloy rivet on the common with black marks around it!
    OK with 3V multimeter test.
    Not OK with 10 Amps of heater current

    S. 😉

    in reply to: leaving appliances safe? #146986
    Simon46
    Participant

    Re: leaving appliances safe?

    On another note if a moulded mains plug is cut off twist the earth pin 90 degrees so a kiddie cannot plug it in.

    S.

Viewing 15 posts - 1,861 through 1,875 (of 2,216 total)