Forum Replies Created
-
AuthorPosts
-
Simon46
ParticipantRe: hotpoint wma 33
Wiring?
S.
Simon46
ParticipantRe: DWI710E1 side panel IWMS
Sorry Smeg. appears to be leaking from seam weld at bottom of side panel. Not enough to be flooding base when i attended but error showed up anyway.
Simon46
ParticipantRe: Bosch SGS43A52GB/04
Would an automotive 8mm hose clip fit? Vauxhall do them
S.
February 9, 2009 at 1:31 pm in reply to: Hotpoint WT400 slimline toploader door lock light flashing #276754Simon46
ParticipantRe: Hotpoint WT400 slimline toploader door lock light flashi
She is calling hotpoint. Many thanks
S.February 7, 2009 at 9:09 pm in reply to: What are the best quality bearings and where do you buy ’em? #259719Simon46
ParticipantRe: What are the best quality bearings and where do you buy
Isnt Yurtesen the expert on this :rotfl:
http://www.ukwhitegoods.co.uk/modules.p … t=yurtesenSimon46
ParticipantRe: The worst Cheneille i have ever seen Pics
A new tenant was moving in to this house in the posh part of town. I was called to it for not emptying 😆 I arrived with Servis pump in hand easy fix i thought. She demanded that the gunk was removed from the machine before she moved in. It did look like something you would find in a toilet.
February 6, 2009 at 1:38 pm in reply to: new door seal rubbing on inner drum of bosch washing machine #276387Simon46
ParticipantRe: new door seal rubbing on inner drum of bosch washing mac
Was it 443455 that was fitted?
S.
January 29, 2009 at 12:52 am in reply to: Re Bosch Stand Alone Siver Dishwasher display dies and reset #275581Simon46
ParticipantRe: Re Bosch Stand Alone Siver Dishwasher display dies and r
Long shot just check the plug isnt stuck to back of dishwasher?
S.
Simon46
ParticipantRe: Hotpoint minstrel plus fridge freezer model 8496N
Cold have a look at
http://www.ukwhitegoods.co.uk/modules.p … pic&t=4509Regards
S.Simon46
ParticipantRe: Smeg DWI612 E8 error
So presumably PCB or valve failed?
S.
Simon46
ParticipantRe: Whirlpool toploader lid doesnt click/start
All done. Leave the lid up when removing switch was where i was going wrong. FYI the spring in the switch had melted into plastic keeping it in off position.
S.
Simon46
ParticipantRe: hpt WM62 hangs
one inlet valve o/c? or brushes.
S.
Simon46
ParticipantRe: Creda E530EW Double Oven Main Oven
Many thanks Jim 😉
S.
Simon46
ParticipantRe: Creda E530EW Double Oven Main Oven
Now ive got this oven to look at and the same relay contacts are dry jointed/burnt out on boost control PCB. Have replaced board and find that all elements and fan are running in side oven mode when switched on ie when the seperate stat is turned up the fan/ fan element comes on but when turned down the fan continues to run. Does it have a timer and i havent left it long enough for the fan to go off? 😕
Fan oven mode appears ok.Regards
SimonSimon46
ParticipantRe: Beko WMA510W completes cycle and starts again
all done. The spigot under sink had backed the hose up with bristles (no drain). this stuff is worse than cheneille!
S.
-
AuthorPosts
