Simon46

Forum Replies Created

Viewing 15 posts - 1,336 through 1,350 (of 2,216 total)
1 2 3 … 89 90 91 … 146 147 148
  • Author
    Posts
  • January 10, 2007 at 9:35 pm in reply to: TDC60S dryness module #199201
    Simon46
    Participant

    Re: TDC60S dryness module

    Replaced module again but also found Earth high resistance (varying)from black wire (module)to cabinet. Stacked on WMA (vibration?).
    Found machine screw loose that earths black wire to module 😮 . Stripped thread on cabinet(painted).
    Made new earth and scratched paint away. Fingers crossed.

    S.

    January 10, 2007 at 9:28 pm in reply to: Tricity bendix impellor change #199566
    Simon46
    Participant

    Re: Tricity bendix impellor change

    Thanks all. Have purchased impellor kit and will see.

    S.

    January 10, 2007 at 9:26 pm in reply to: VTD00 interlock fitting #200184
    Simon46
    Participant

    Re: VTD00 interlock fitting

    Thanks all. Didnt get to see posts so did it fom the front.

    S.

    January 8, 2007 at 11:12 am in reply to: Hotpoint TDC62P will not start. #199877
    Simon46
    Participant

    Re: Hotpoint TDC62P will not start.

    If wiring to replacement heater was done correctly i would suspect dryness module. Power off if you are going to look yourself.

    Regards
    Simon

    January 7, 2007 at 11:58 am in reply to: Whirlpool ADG 6340 #199838
    Simon46
    Participant

    Re: Whirlpool ADG 6340

    Check filter is not blocked and rinse aid dispenser gasket has not failed missing causing excessive rinse aid to be leaked during wash (Overfoaming)

    Regards
    Simon

    January 7, 2007 at 11:51 am in reply to: Hotpoint WM65 going through timers #199720
    Simon46
    Participant

    Re: Hotpoint WM65 going through timers

    Just try and report back if there is any change in operation.

    Regards
    S

    January 7, 2007 at 10:38 am in reply to: Bosch KGV 2620 – how to change reversible fridge door #199830
    Simon46
    Participant

    Re: Bosch KGV 2620 – how to change reversible fridge door

    http://www.bshappliancecare.com/Bosch/boschspares.html
    may help you with diagrams.

    Regards
    Simon

    January 7, 2007 at 10:29 am in reply to: Hotpoint WM65 going through timers #199718
    Simon46
    Participant

    Re: Hotpoint WM65 going through timers

    First of all i would try connecting hot and cold inlet valves to cold tap.

    Regards
    Simon

    January 7, 2007 at 8:52 am in reply to: Hotpoint WM65 going through timers #199716
    Simon46
    Participant

    Re: Hotpoint WM65 going through timers

    Are both inlet valves connected to cold water IE a y piece which both hoses are connected to.

    Regards
    Simon

    January 4, 2007 at 10:09 pm in reply to: Hotpoint Mistral plus #199602
    Simon46
    Participant

    Re: Hotpoint Mistral plus

    The fan behind the fridge i take it. usually a fuse in line. did he try that do you know?

    Regards
    S

    January 2, 2007 at 9:36 pm in reply to: TDC60S dryness module #199200
    Simon46
    Participant

    Re: TDC60S dryness module

    :worthy:
    S.

    January 2, 2007 at 6:07 pm in reply to: TDC60S dryness module #199198
    Simon46
    Participant

    Re: TDC60S dryness module

    Thanks Martin. Also the programmed dry setting doesnt finish and the timed has no tumble cool. 😕 has anybody got a wiring diagram for this in the unlikely event a connector may have been put on incorrectly?

    Thanks
    Simon

    January 2, 2007 at 3:23 pm in reply to: Bosch Washer/Dryer #199210
    Simon46
    Participant

    Re: Bosch Washer/Dryer

    E-Nr required please.

    Regards
    Simon

    January 2, 2007 at 10:09 am in reply to: Bypassing Danfoss fridge thermostat in Westinghouse BJ414 #199174
    Simon46
    Participant

    Re: Bypassing Danfoss fridge thermostat in Westinghouse BJ41

    The white wire will probably be a heater to assist defrost.

    Regards
    S.

    December 31, 2006 at 11:12 am in reply to: Hotpoint WD420 #199005
    Simon46
    Participant

    Re: Hotpoint WD420

    One of the inlet valves is leaking (hot or cold). Power off if you are going to look yourself.

    Regards
    Simon

  • Author
    Posts
Viewing 15 posts - 1,336 through 1,350 (of 2,216 total)
1 2 3 … 89 90 91 … 146 147 148