Simon46

Forum Replies Created

Viewing 15 posts - 1,351 through 1,365 (of 2,216 total)
1 2 3 … 90 91 92 … 146 147 148
  • Author
    Posts
  • December 31, 2006 at 11:06 am in reply to: Hpt td #199074
    Simon46
    Participant

    Re: Hpt td

    Yes tool available.

    S.

    December 31, 2006 at 11:05 am in reply to: Hotpoint DC27 Dishwasher flashing Prewash light #199073
    Simon46
    Participant

    Re: Hotpoint DC27 Dishwasher flashing Prewash light

    Sounds like a flooded base. Unplug appliance, tilt backward onto towels and see if water runs out. If fault comes back there is a leak. Dont use 3 in one tablets.

    Regards Simon

    December 30, 2006 at 12:28 pm in reply to: zanussi aquasave zd694, no water going in! #199024
    Simon46
    Participant

    Re: zanussi aquasave zd694, no water going in!

    This may explain your problem.
    http://www.ukwhitegoods.co.uk/modules.p … ge&pid=104

    Repairs@ for an engineer if needed. Power off if you are going to look yourself.

    Regards
    Simon

    December 30, 2006 at 10:43 am in reply to: Zanussi Aquacycle 1200 – we have no hot water supply #199022
    Simon46
    Participant

    Re: Zanussi Aquacycle 1200 – we have no hot water supply

    As long as there is water supply to the hot inlet valve the machine will take care of it. Other wise a Y piece so that both hoses are connected to the cold water will be required. (see link below)

    http://tinyurl.com/yjvby5

    Regards
    Simon

    December 29, 2006 at 7:55 pm in reply to: Hotpoint WD420 #199003
    Simon46
    Participant

    Re: Hotpoint WD420

    Clean or dirty water? try turning off the inlet valves on house plumbing. or backfilling from sink waste. raise hose to come down to spigot on sink trap.

    Regards
    Simon

    December 28, 2006 at 10:03 pm in reply to: whirlpool adp5966 error code F6 #198955
    Simon46
    Participant

    Re: whirlpool adp5966 error code F6

    That hose will have to be sorted. The pressure it has inside it is immense. Worm drive clips is the answer. Is the appliance filling with water?

    Regards
    S.

    December 28, 2006 at 9:47 pm in reply to: Caple DI414 – fills but then nothing #198941
    Simon46
    Participant

    Re: Caple DI414 – fills but then nothing

    Allow to dry out 24hrs and see what happens. Power off of course.

    Regards
    S.

    December 28, 2006 at 9:40 pm in reply to: Whirlpool ADP4601 constant flashing #192438
    Simon46
    Participant

    Re: Whirlpool ADP4601 constant flashing

    Went back to address to fix oven door today and no F1 seen yet. 😕

    S

    December 28, 2006 at 9:35 pm in reply to: Bosch 1600 Express LogiXX – WFR3267GB #198932
    Simon46
    Participant

    Re: Bosch 1600 Express LogiXX – WFR3267GB

    Module had failed on my own wfr2860. Came with a spin fault that it would go to maximum speed straight away on spin. Power supply failed on board (flashed Bereit). Was an expensive repair but i checked everything else first to prove all was ok. Power off if you are going to have a look yourself.

    Regards
    Simon

    December 28, 2006 at 2:01 pm in reply to: Ariston AL1256T #198916
    Simon46
    Participant

    Re: Ariston AL1256T

    Selfbore. Have seen them last 6 months.

    S.

    December 28, 2006 at 1:35 pm in reply to: Ariston AL1256T #198914
    Simon46
    Participant

    Re: Ariston AL1256T

    If they are crutch handle taps yes. If they are the blue and red plastic 90 degree turn handle ones then the tops can spin on the valve and not open. If selfbore (clamped onto pipe) can scale up and block flow.

    S.

    December 28, 2006 at 1:18 pm in reply to: Ariston AL1256T #198912
    Simon46
    Participant

    Re: Ariston AL1256T

    Has the cold hose got the tap turned on on the house plumbing? Humming might be cold valve asking for water but no supply.

    Regards
    Simon

    December 28, 2006 at 8:00 am in reply to: Dow corning high temp silicone #198907
    Simon46
    Participant

    Re: Dow corning high temp silicone

    Thanks Toni
    😀
    S.

    December 27, 2006 at 12:47 pm in reply to: Indesit WE14 #198855
    Simon46
    Participant

    Re: Indesit WE14

    It will probably damage the sealing faces of the filter. Would possibly then require new pump and filter assy.

    S.

    December 27, 2006 at 12:44 pm in reply to: Hotpoint aquarius wma32 1200 spin #198867
    Simon46
    Participant

    Re: Hotpoint aquarius wma32 1200 spin

    I would recommend an engineer with the relevant diagnostic equipment. Have a look at Repairs@ for one.

    Regards
    Simon

  • Author
    Posts
Viewing 15 posts - 1,351 through 1,365 (of 2,216 total)
1 2 3 … 90 91 92 … 146 147 148