Forum Replies Created
-
Posts
-
Re: Samsung RS 20CCSV
Just RS20CCSV Single evaporator unit in freezer for both.
Fault code on the freezer digit 8 lower right illuminated which states evap sensor.
Have already replaced it, so assuming its faulty one? as it freezing down fine, temp recorded -18 on display but just blocked solid so fridge is warm.Defrost heaters seem ok, however tried getting into forced defrost just would not do it. Never seem to get these things into a test mode 😳
Re: Ise5 conditioner
Has this fault just appeared, or has it been like it from day one?
What is the water pressure like?
Your probably aware, (so not telling you how to suck eggs) that the rinse requires both valves to send water through the pipes equally, directing the water into the fabric. Could it be that its not filling quick enough to fill that chamber properly?
To test the comfort valve instead of sitting and waiting for ages while it does a rinse, short the valves out so they both operate at the same time.
I had this type a fault on a soverign,a year or so ago. replaced the draw and outer compartment, seem to cure that one. But water pressure was a problem as well.
Re: Ise5 conditioner
bazza500 wrote:The very first ISE2 I installed definately had this valve stutter. You could hear the valve open as the door released and the sound of water filling. The door then locked again and the water stopped. It repeated this until switched off.
Exactly as bazza said, it pulses on and off constantly until door lock light goes out. As it does it, it can cause the pipes to knock as a though its an air lock. I have had a few some times door lock other times both pcb and lock.
Ken definatly not syphoning.
& Its totally different to the fault on the 5-2. This actually operates the valve for 3 seconds then switches straight off carries on washing.
Jim.
The only other door lock that I find will fit is the pattern hotpoint, for some reason the genuine hole is a bit small, and will jam.
The same with the new ISE door locks i was sent last time the screw holes are much larger and you need to find new screws, as this can also jam if not tight enough.
Re: Ise5 conditioner
I have spent hours trying to trace this fault, it is strange that the only thing that can operate the valve is a supply from the pcb. So normally this would be the first port of call, I know the issue of the door locks and this fault is cured on the ise2 by doing this.
Although the valves are rated at normal mains voltage am i right in saying that it is only 12v from the board that is required to operate them?
So could it be that its picking a low voltage supply from somewhere else possible motor pcb? As this is the only real difference between the machines because of the induction motor. This is the only thing I have not tried myself.
Maybe its worth trying this on yours Jim to see if it does sort this fault.
Steven
Re: LG auto wm-14225fd
email: spares@jtmcontracts.com or 0191 387 0778.
I not sure if EMW can repair as these boards as all components are gelled?
Re: neff S4340X0GB/20 sticking in cycles!!!
Have you checked for broken wires in the door loom?
or is it getting too hot and just cycling on the overheat thermostat?
Steven
Re: Ise5 conditioner
iadom wrote:To come back to this Steven, what is the situation as regards your customer, has she been left to live with it or are you still waiting for a resolution from ISE Tech support?
Jim.
Customer putting up with it, until we find a cure.
The problem i have found with a few of the ise2 is with the valve stuttering on and off at the end of the spin programe just before the door light flashes, when it de engergises it stops. Sometimes door lock, on occasions found had to change pcb as well.
Re: Ise5 conditioner
Jim
No never got to the bottom of it despite loads of time trying.
Door lock and top pcb, replaced to no avail.
it would only happen on the final rinsing just before spin, the valve would spirt water for a fraction of a second enough to fill the conditioner but not quite enough to syphon.
The only thing i did not try was a pressure switch.
Its got to be some kind of glitch in the software allowing low voltage to the valves enough to operate them.
So you could start pressure switch?
Sean was trying to get some feed back from Vestel techincal on the subject, but have had no reply on that.
sorry I cant be of any more help.
Steven
Re: ISE website
I expect Ken Or John will reply, but the last time I spoke to them the new brochure is being updated, with just the 10s and the new 2 Aw23.
Ken was working on the first press so ironing out some mistakes before going to print, so should not be too long for a pdf copy is available.
If your desperate for info then the ukwhitegoods site has most of the information about the appliances currently available, if you want a the draft copy of pdf then I can let you have a copy. I have printed and used as a tempory measure until the new brochure become availble.
Hope this helps
Steven
