suedehead1

Forum Replies Created

Viewing 15 posts - 316 through 330 (of 1,348 total)
1 2 3 … 21 22 23 … 88 89 90
  • Author
    Posts
  • January 16, 2016 at 3:30 pm in reply to: Whirlpool Top Loader Valve #434507
    suedehead1
    Participant

    Re: Whirlpool Top Loader Valve

    qualtex have one VAL22

    November 28, 2015 at 10:00 am in reply to: Hoover dyn9164dpg #433141
    suedehead1
    Participant

    Re: Hoover dyn9164dpg

    it had jammed it had stuck for 6 hours wouldnt even unlock banging the door,
    had to break the interlock to get it open,

    November 19, 2015 at 8:11 pm in reply to: beko dsc85w dryer #432909
    suedehead1
    Participant

    Re: beko dsc85w dryer

    yes it heatsi will check ntc thanks

    November 3, 2015 at 7:15 pm in reply to: beko wmi71641 #432140
    suedehead1
    Participant

    Re: beko wmi71641

    Hi its doing it on every load checked carbons etc I would try a new board if I could find the part number

    October 28, 2015 at 7:35 am in reply to: BEKO WMA520S PCB? #317892
    suedehead1
    Participant

    Re: BEKO WMA520S PCB?

    hi i got a pcb from connect for the same machine from connect 5045173414495
    it doesnt seem to work properly is it unprogrammed or the wrong pcb?

    October 28, 2015 at 7:18 am in reply to: Whirlpool ADG7800/1 #410494
    suedehead1
    Participant

    Re: Whirlpool ADG7800/1

    Hi I have one of these showing E1 F8 any ideas welcomed

    October 18, 2015 at 10:12 pm in reply to: zanussi dishwasher esl6115 #431711
    suedehead1
    Participant

    Re: zanussi dishwasher esl6115

    its a very small thing it plugs into the sump

    September 17, 2015 at 7:57 pm in reply to: Indesit sixl 145 s UK taking water during a wash #430374
    suedehead1
    Participant

    Re: Indesit sixl 145 s UK taking water during a wash

    did you check for a hole in the pressure switch tube

    September 17, 2015 at 7:54 pm in reply to: Booby-trapped Hotpoint Washers #430357
    suedehead1
    Participant

    Re: Booby-trapped Hotpoint Washers

    these machines are a bloody nuisance I have hada couple of blocked pumps which ended up needing pcb reprogrammed there must be a foolproof way of avoiding this happening.

    September 10, 2015 at 9:05 pm in reply to: creda 48347 cooker #430204
    suedehead1
    Participant

    Re: creda 48347 cooker

    thanks

    September 10, 2015 at 9:04 pm in reply to: rubbish non genuine dryer capacitors #427627
    suedehead1
    Participant

    Re: rubbish non genuine dryer capacitors

    spoke to Saleem at connect he says they have had no complaints abouy capacitors

    September 6, 2015 at 7:59 am in reply to: rubbish non genuine dryer capacitors #427625
    suedehead1
    Participant

    Re: rubbish non genuine dryer capacitors

    I have an epidemic of capacitor failures after fitting non genuine capacitors.
    I get them from qualtex and connect but couldnt work out where the bad ones were coming from.
    It seems to be DOMOPART capacitors from connect which are the worse.

    July 21, 2015 at 6:56 am in reply to: Fixed labour fee ,fitting parts supplied by customer ? #428900
    suedehead1
    Participant

    Re: Fixed labour fee ,fitting parts supplied by customer ?

    if your getting paid fit the part if it doesnt work its the customers fault not yours.

    July 20, 2015 at 8:11 pm in reply to: bosch dishwasher E14 #428984
    suedehead1
    Participant

    Re: bosch dishwasher E14

    Things are way to complicated these days. Thanks

    July 14, 2015 at 7:00 pm in reply to: bosch wvt12842gb/06 #344302
    suedehead1
    Participant

    Re: bosch wvt12842gb/06

    dot another of these E06 tried everything already mentioned, the problem with this one is it runs for about 10 minutes then E06 appears soit hasnt even got to the draining stage any ideas welcomed

  • Author
    Posts
Viewing 15 posts - 316 through 330 (of 1,348 total)
1 2 3 … 21 22 23 … 88 89 90