suedehead1

Forum Replies Created

Viewing 15 posts - 301 through 315 (of 1,348 total)
1 2 3 … 20 21 22 … 88 89 90
  • Author
    Posts
  • June 28, 2016 at 8:02 pm in reply to: Hotpoint dryer motor bearings #438934
    suedehead1
    Participant

    Re: Hotpoint dryer motor bearings

    Great I will go armed with 2 off each thanks

    June 28, 2016 at 8:01 pm in reply to: Candy GV1410TW3W handle #438931
    suedehead1
    Participant

    Re: Candy GV1410TW3W handle

    Thanks very much

    June 8, 2016 at 5:59 pm in reply to: samsung WF431ABP washing machine #438376
    suedehead1
    Participant

    Re: samsung WF431ABP washing machine

    Thanks very much greatly appreciated guys

    June 3, 2016 at 7:01 pm in reply to: Culina CD650 oven #438146
    suedehead1
    Participant

    Re: Culina CD650 oven

    Thanks very much

    May 28, 2016 at 12:01 pm in reply to: indesit iwdc 6105 #438011
    suedehead1
    Participant

    Re: indesit iwdc 6105

    Dryer ntc

    May 16, 2016 at 7:20 pm in reply to: AEG Dishwasher not filling, #423887
    suedehead1
    Participant

    Re: AEG Dishwasher not filling,

    Hi I dont know if you managed to get this one resoled I have the same problem with the same model

    May 16, 2016 at 7:07 pm in reply to: Help diagnosing e20 on AEG Favorit 55002 VI #416232
    suedehead1
    Participant

    Re: Help diagnosing e20 on AEG Favorit 55002 VI

    Hi I decided to jump on an existing thread.
    I was at the exact same dishwasher model and pnc the same.
    the dishwasher overfills then the pump kicks in then it overfills again and so on.
    The customer fitted a new pressure switch from AEG but its still the same.
    I couldnt get any assurances from the customer that he hadnt blown down the new pressure switch.

    no blockages or water in the base.

    any ideas welcomed

    March 20, 2016 at 11:17 pm in reply to: adp8132 fault #436147
    suedehead1
    Participant

    Re: adp8132 fault

    check for broken wires at the bottom of the door.

    March 15, 2016 at 8:39 pm in reply to: Beko wmb81445lw #435067
    suedehead1
    Participant

    Re: Beko wmb81445lw

    how do you do a factory reset

    March 15, 2016 at 7:42 am in reply to: Beko wmb81445lw #435065
    suedehead1
    Participant

    Re: Beko wmb81445lw

    i have a problem with the same machine when you try to set a program it just flashes 28 the end and wont do anything any advice on fault or how to access codes welcomed.

    March 14, 2016 at 9:19 pm in reply to: Whirlpool top loader drive. #436201
    suedehead1
    Participant

    Re: Whirlpool top loader drive.

    I never take the cabinet off tip it back take off 2 bolts holding on the big spring clips and your there.

    February 17, 2016 at 7:58 am in reply to: Whirlpool to do a recall on Hotpoint dryers #431307
    suedehead1
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    I am loosing work due to this recall. Faulty Hotpoint dryers have been a big part of my workload. They are unreliable but easy to fix I am sure other engineers like me have made a lot of money changing belts, teardrop bearings, fans, water pumps and heaters. I hope whirlpool continue with the same unreliable design.
    I would rather change a belt on a hotpoint condenser dryer than change that stupid small belton a beko or change a bel on a white knight condendser dryer, and dont get me started on heat pump dryers.

    February 5, 2016 at 7:30 am in reply to: hotpoint dishwasher bfi620 module #435075
    suedehead1
    Participant

    Re: hotpoint dishwasher bfi620 module

    thanks i must work out these date codes at some point

    January 27, 2016 at 7:22 am in reply to: kuppersbusch american style fridge freezer #434803
    suedehead1
    Participant

    Re: kuppersbusch american style fridge freezer

    thanks guys I will take a look

    January 26, 2016 at 9:40 pm in reply to: Whirlpool to do a recall on Hotpoint dryers #431224
    suedehead1
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    I had a guy on the phone he had his condenser dryer modification done.
    the belt was broken on it when the engineer came out, the engineer did the modification but refused to change the belt.
    Is this normal practice. whats the point of carrying out a modification and
    leaving the dryer not working.

  • Author
    Posts
Viewing 15 posts - 301 through 315 (of 1,348 total)
1 2 3 … 20 21 22 … 88 89 90