suedehead1

Forum Replies Created

Viewing 15 posts - 571 through 585 (of 1,348 total)
1 2 3 … 38 39 40 … 88 89 90
  • Author
    Posts
  • August 24, 2011 at 7:14 pm in reply to: stoves hob #357645
    suedehead1
    Participant

    Re: stoves hob

    thanks very much.

    August 17, 2011 at 9:27 pm in reply to: Bosch d/w SG45E02GB/56 #357422
    suedehead1
    Participant

    Re: Bosch d/w SG45E02GB/56

    blockage in the clear plastic tube at the front right hand side.

    August 15, 2011 at 9:20 pm in reply to: Hoover VHC 392 #357302
    suedehead1
    Participant

    Re: Hoover VHC 392

    most likely belt tension pulleys or drum support wheels but the rear bearing also squeaks.

    August 13, 2011 at 6:02 pm in reply to: neff washer dryer #357153
    suedehead1
    Participant

    Re: neff washer dryer

    thanks for the replies guys it looks like i will need to dig it out and have a look.

    August 12, 2011 at 6:33 pm in reply to: neff washer dryer #357150
    suedehead1
    Participant

    Re: neff washer dryer

    i take it we are not big fans of clifton-services.com
    i dont think its the door lock as it works on a 30 degree program but not on a hotter wash.
    i was hoping it was heater or thermister but its really badly built in i will need to demolish the house to get a look.

    August 11, 2011 at 8:50 pm in reply to: Oh Helen where did I go wrong? #357108
    suedehead1
    Participant

    Re: Oh Helen where did I go wrong?

    i have never had to take one off they usually are already off before i fit a new one, i never remove the plug because i dont care. if i was advocating someone to change one surely gloves safety glasses and a safety balustrade should be used.

    August 10, 2011 at 10:06 pm in reply to: howden HJA8640 dishwasher #356757
    suedehead1
    Participant

    Re: howden HJA8640 dishwasher

    sorry to bring this one up again i went back today and definately cancelled the program, but when i restarted it it did exactly the same, i would normally give up but the customer is very keen to get it fixed, any help would be gratefully received.

    August 5, 2011 at 7:11 pm in reply to: Baumatic / Servis? #356785
    suedehead1
    Participant

    Re: Baumatic / Servis?

    if you go on qualtex site and type in merloni knob does it look like any of those?

    August 4, 2011 at 9:52 pm in reply to: howden HJA8640 dishwasher #356756
    suedehead1
    Participant

    Re: howden HJA8640 dishwasher

    hi,
    i cancelled the existing program and triedit on different programs, it does exactly the same on evey program
    a slight humming noise for a couple of secondsthe4 or 5 clicks then nothing, i also checked it was getting water.

    August 4, 2011 at 9:47 pm in reply to: indesit IWDC6125 #356754
    suedehead1
    Participant

    Re: indesit IWDC6125

    thanks Jim

    July 12, 2011 at 9:05 pm in reply to: HOOVER NEW WAVE i only change carbons #355373
    suedehead1
    Participant

    Re: HOOVER NEW WAVE i only change carbons

    it will be the armature in the motor, it used to be supplied seperately, i usually try an old soft wave motor.

    July 12, 2011 at 9:01 pm in reply to: candy oven #355363
    suedehead1
    Participant

    Re: candy oven

    no i didnt think of that its a good idea i will give it a try,

    July 10, 2011 at 6:55 pm in reply to: vhd9163 lower concrete weight #355207
    suedehead1
    Participant

    Re: vhd9163 lower concrete weight

    excellent thanks very much.

    July 8, 2011 at 6:11 pm in reply to: Hoover washing machine 8yrs old #355032
    suedehead1
    Participant

    Re: Hoover washing machine 8yrs old

    C

    July 7, 2011 at 10:16 pm in reply to: Hoover washing machine 8yrs old #355029
    suedehead1
    Participant

    Re: Hoover washing machine 8yrs old

    look for dry soldered joints on relays on small pcb.

  • Author
    Posts
Viewing 15 posts - 571 through 585 (of 1,348 total)
1 2 3 … 38 39 40 … 88 89 90