suedehead1

Forum Replies Created

Viewing 15 posts - 556 through 570 (of 1,348 total)
1 2 3 … 37 38 39 … 88 89 90
  • Author
    Posts
  • September 20, 2011 at 10:17 pm in reply to: Creda TCR2 #306643
    suedehead1
    Participant

    Re: Creda TCR2

    you just get a new latch kit C00257618 comes with the catch and part for front panel change both parts.

    September 19, 2011 at 7:49 pm in reply to: matsui mf2s/a dw #359294
    suedehead1
    Participant

    Re: matsui mf2s/a dw

    thermostat screwed into underside of the base would be worth checking if you can find it.

    September 19, 2011 at 7:45 pm in reply to: vtd60 #359257
    suedehead1
    Participant

    Re: vtd60

    i would check the thermostats.

    September 13, 2011 at 6:24 pm in reply to: awo/das148 door seal #358703
    suedehead1
    Participant

    Re: awo/das148 door seal

    suedehead1 wrote:hi i am looking for a door seal for this machine,
    the part no. listed is 481246068615 but it is obsolete.
    it said use part no.481246068617 but it wont fit.
    the plastic tub has plastic location lugs which fit into slots in the door seal,
    the new seal doesnt have slots for the lugs.
    i dont know what to do? do i cut the lugs off or what,
    any ideas welcome thanks.

    sorry to give this a wee bump but i am stuck.

    September 8, 2011 at 8:50 pm in reply to: bbc watchdog #333006
    suedehead1
    Participant

    Re: bbc watchdog

    i see comets misselling of warranties on watchdog tonight,
    give it a couple of weeks and it will be back to the same old story.

    September 6, 2011 at 10:16 pm in reply to: ariston w/dryer cde12xuk #358410
    suedehead1
    Participant

    Re: ariston w/dryer cde12xuk

    you need to get the right one they arent interchangeable.

    September 3, 2011 at 4:51 pm in reply to: fisher paykel dd603 #354133
    suedehead1
    Participant

    Re: fisher paykel dd603

    thanks.

    September 2, 2011 at 9:00 pm in reply to: fisher paykel dd603 #354131
    suedehead1
    Participant

    Re: fisher paykel dd603

    thanks, does that mean it needs a new motor? do you know the part number?
    thanks.

    September 2, 2011 at 8:17 pm in reply to: fisher paykel dd603 #354129
    suedehead1
    Participant

    Re: fisher paykel dd603

    hi again the customers been abroad thankfuly but i went back to the dishwasher today,
    the bottom drawer motor has seized i pulled of the blue impellorand the shaft wont turn,i have the service manual but its not entirley clear.
    could there be a foreign object jamming the motor is it easy to take off to check.

    September 1, 2011 at 10:04 pm in reply to: bosch d/w no heat #358139
    suedehead1
    Participant

    Re: bosch d/w no heat

    did you check for a dry joint on the pcb.?

    August 26, 2011 at 9:09 pm in reply to: Baumatic BWD 12 #357786
    suedehead1
    Participant

    Re: Baumatic BWD 12

    servis derived machine pcb fault.

    August 26, 2011 at 9:04 pm in reply to: Hoover se147 31002754 #357757
    suedehead1
    Participant

    Re: Hoover se147 31002754

    the paddle just clips on like the hotpoint ones no screws.

    August 26, 2011 at 9:01 pm in reply to: Spot that appliance #357865
    suedehead1
    Participant

    Re: Spot that appliance

    coronation street gails kitchen zanussi washing machine an old one grey front.

    August 25, 2011 at 8:50 pm in reply to: howden HJA8640 dishwasher #356759
    suedehead1
    Participant

    Re: howden HJA8640 dishwasher

    i poured a basin of water into it and for some reason it is now working ok.
    thanks for the replies.

    August 25, 2011 at 8:48 pm in reply to: neff washer dryer #357154
    suedehead1
    Participant

    Re: neff washer dryer

    the fault was the dryer thermostat needed reset,
    its now working fine.

  • Author
    Posts
Viewing 15 posts - 556 through 570 (of 1,348 total)
1 2 3 … 37 38 39 … 88 89 90