Washman

Forum Replies Created

Viewing 15 posts - 511 through 525 (of 894 total)
1 2 3 … 34 35 36 … 58 59 60
  • Author
    Posts
  • March 19, 2008 at 12:14 pm in reply to: Changing Door Swing on Zanussi ZDE57140W Dryer? #246406
    Washman
    Participant

    Re: Changing Door Swing on Zanussi ZDE57140W Dryer?

    Hi

    Door is fully reversible.

    You need to make sure plug is removed from socket then remove top , undo door lock, and move lock to other side of cabinet. Making sure that the wiring is secure and safe. If in any dought call Zanussi or your local independent engineer.

    Mike

    March 16, 2008 at 6:32 pm in reply to: Servis Service #245897
    Washman
    Participant

    Re: Servis Service

    Hi

    Yes I have found a great improvement from GB DAR , and receive parts much quicker and back up is much better from Servis.

    Mike

    March 15, 2008 at 4:43 pm in reply to: AEG T57560 condenser drier no heat #245838
    Washman
    Participant

    Re: AEG T57560 condenser drier no heat

    Hi

    New element required

    Mike

    March 13, 2008 at 6:58 pm in reply to: washer dryer APM8703 not drying #245705
    Washman
    Participant

    Re: washer dryer APM8703 not drying

    Hi

    The half load switch must be selected before the dryer will work.

    Mike

    March 13, 2008 at 6:53 pm in reply to: pat tester #245410
    Washman
    Participant

    Re: pat tester

    Hi

    Bought mine off Ebay for £50.00.

    Mike

    March 13, 2008 at 6:51 pm in reply to: I’ve found it!!!!!!!!! #245763
    Washman
    Participant

    Re: I’ve found it!!!!!!!!!

    Hi

    Is it made of Gold or some other expensive metal.

    Mike

    March 7, 2008 at 4:04 pm in reply to: w/pool top loader #245218
    Washman
    Participant

    Re: w/pool top loader

    Hi

    No . You will need kit WPL481932528035 Clutch coupling.

    Mike

    March 4, 2008 at 3:50 pm in reply to: SERVIS 1300 DOES NOT SPIN PROPERLY #244911
    Washman
    Participant

    Re: SERVIS 1300 DOES NOT SPIN PROPERLY

    Hi

    Have you checked the pressure switch tube , ie: when you removed the hose from pressure switch you blew down the tube.
    Posibly the pressure chamber on the sump hose underneath is blocked.

    Mike

    Switch off and pull plug out before checking.

    March 3, 2008 at 7:31 pm in reply to: BEKO WMB10W. Timer ?? #244778
    Washman
    Participant

    Re: BEKO WMB10W. Timer ??

    Hi

    Yes that is the correct function , the module controls the programming.

    Mike

    March 3, 2008 at 6:55 pm in reply to: BEKO WMB10W. Timer ?? #244776
    Washman
    Participant

    Re: BEKO WMB10W. Timer ??

    Hi

    Timer will advance to correct position, if you check user manual page 9.

    “To start the programme , press the On/Off button The indicator will light and the closed door will be locked in a few seconds. The programmer knob will rotate and advance to the correct point to commence washing . This is a normal function of the programmer.”

    February 28, 2008 at 8:01 pm in reply to: Samsung P1253 Excess Vibration + Spinning problems!! #244521
    Washman
    Participant

    Re: Samsung P1253 Excess Vibration + Spinning problems!!

    Hi

    Have you checked the filter and pump housing and the drain hose.

    Mike

    February 23, 2008 at 9:49 am in reply to: Beko VMA 510W #244023
    Washman
    Participant

    Re: Beko VMA 510W

    Hi

    Have you checked motor tacho.

    Mike

    February 23, 2008 at 9:47 am in reply to: beko wma 1614 #243921
    Washman
    Participant

    Re: beko wma 1614

    Hi

    Change Module that is the only way , out of balance detection is corrupt it can think it is out of balance with drum empty.
    I have changed a lot of these. New boards have had the software re written to make them less sensitive to out of balance problems.

    Mike

    February 22, 2008 at 6:45 pm in reply to: Servis M6160w #243988
    Washman
    Participant

    Re: Servis M6160w

    Hi

    Qualtex do a nice carbon brush catalgue with photos and scaled drawings


    Mike

    February 20, 2008 at 6:44 pm in reply to: Servis M6006 — NO SPIN??? #243734
    Washman
    Participant

    Re: Servis M6006 — NO SPIN???

    Hi

    Is the water level switch resetting when drum is empty.

  • Author
    Posts
Viewing 15 posts - 511 through 525 (of 894 total)
1 2 3 … 34 35 36 … 58 59 60