allan73

Forum Replies Created

Viewing 15 posts - 226 through 240 (of 497 total)
1 2 3 … 15 16 17 … 32 33 34
  • Author
    Posts
  • February 8, 2011 at 9:43 pm in reply to: Hotpoint 9536 s/n 83183406 Suspension given up. #344049
    allan73
    Participant

    Re: Hotpoint 9536 s/n 83183406 Suspension given up.

    The leg was the right side looking from the front, on the later ones I did in the past the rods had jumped out and sometimes damaged the top plastic part of the damper.
    I changed the armature on this about 12 months back and the motor and taco both seem fine, the speed surge is not constant hence I suspect the timer.

    February 8, 2011 at 8:52 pm in reply to: Hotpoint 9536 s/n 83183406 Suspension given up. #344046
    allan73
    Participant

    Re: Hotpoint 9536 s/n 83183406 Suspension given up.

    Thanks for the replies 🙂
    The timer is the early one with the module clipped to the side and I’m sure I’ve been told these can suffer from sudden surging.

    I’ve fitted the full suspension kit to later wm’s in past but wasn’t sure if it was still available or if it would fit this 95 series.

    Allan.

    February 7, 2011 at 6:46 pm in reply to: white knight wk1400v drum lifters off #343074
    allan73
    Participant

    Re: white knight wk1400v drum lifters off

    Just to update this, the lifters clip in as the hotpoint wma/wf but are a much tighter fit 😡

    February 3, 2011 at 10:25 am in reply to: hotpoint aqxgf149 p1 #343458
    allan73
    Participant

    Re: hotpoint aqxgf149 p1

    Have you checked the heater for low insulation ?

    February 2, 2011 at 8:42 pm in reply to: Hotpoint WF320P – Drum bearings – be aware… #341731
    allan73
    Participant

    Re: Hotpoint WF320P – Drum bearings – be aware…

    You cannot put 35mm bearings into a 30mm rear half, you must change the complete rear half.

    Allan

    January 31, 2011 at 4:38 pm in reply to: white knight wk1400v drum lifters off #343073
    allan73
    Participant

    Re: white knight wk1400v drum lifters off

    I’m pretty sure these are the same as some of the matsui M/c’s by the way 😉

    January 28, 2011 at 8:53 pm in reply to: Samsung p1453 pump #342828
    allan73
    Participant

    Re: Samsung p1453 pump

    A run of the mill askol should fit but might be worth checking if the original pump has a toc fitted and replace accordingly.
    Hope this helps Allan.

    January 28, 2011 at 9:44 am in reply to: Numatic NVQ 250B motor #342786
    allan73
    Participant

    Re: Numatic NVQ 250B motor

    My cousin say’s can you post a photo of your motor ?

    Allan

    January 27, 2011 at 8:24 pm in reply to: Numatic NVQ 250B motor #342785
    allan73
    Participant

    Re: Numatic NVQ 250B motor

    When I get in work in the morning I’ll ask my cousin Micky, what SHE doesn’t know about vaccum cleaners isn’t worth knowing 😉

    January 27, 2011 at 5:54 pm in reply to: Whirlpool AWO4505/D not ramping into spin #342718
    allan73
    Participant

    Re: Whirlpool AWO4505/D not ramping into spin

    Thanks for that Chezza, I thought I’d read something on here about belts being a problem on some whirlpool’s 😉

    January 25, 2011 at 7:03 pm in reply to: Hotpoint WMD 960 #325884
    allan73
    Participant

    Re: Hotpoint WMD 960

    Can I ask if you ever got to the bottom of this one Winker ? I came across one of these doing the same today and I’m wondering if I should send the customer to hotpoint ❓

    Allan.

    January 22, 2011 at 7:09 pm in reply to: Old belling format 6061c halagon lamp not working #342095
    allan73
    Participant

    Re: Old belling format 6061c halagon lamp not working

    Just realised I spelt halogen wrong 😳

    January 16, 2011 at 8:29 am in reply to: Hotpoint dryer TCL770G ntc resistance #341233
    allan73
    Participant

    Re: Hotpoint dryer TCL770G ntc resistance

    Thanks Jim 8)

    January 14, 2011 at 4:19 pm in reply to: Samsung W/machines #341067
    allan73
    Participant

    Re: Samsung W/machines

    You can fit askol pumps on these I think.

    January 13, 2011 at 6:31 pm in reply to: Hoover OPH 714D/1-80 #340901
    allan73
    Participant

    Re: Hoover OPH 714D/1-80

    I’d change the heater anyway, sometimes the heaters go down when they’ve been on a while on these.

  • Author
    Posts
Viewing 15 posts - 226 through 240 (of 497 total)
1 2 3 … 15 16 17 … 32 33 34