allan73

Forum Replies Created

Viewing 15 posts - 286 through 300 (of 497 total)
1 2 3 … 19 20 21 … 32 33 34
  • Author
    Posts
  • November 4, 2010 at 7:45 pm in reply to: new washers #334950
    allan73
    Participant

    Re: new washers

    Beko’s aren’t too bad for a cheapo m/c and the spares are usually reasonable.

    November 4, 2010 at 7:41 pm in reply to: Hoover HSWD 166-80. #335017
    allan73
    Participant

    Re: Hoover HSWD 166-80.

    Thanks Bob, I thought that would be the culprit 8)

    November 4, 2010 at 7:00 pm in reply to: Hotpoint FDW60 leak from sump. #334894
    allan73
    Participant

    Re: Hotpoint FDW60 leak from sump.

    Thanks for the info Iadom, very helpful 😉

    Do you know if the seal can be bought separately or will it require a new sump ❓

    Allan.

    October 29, 2010 at 7:12 pm in reply to: Hotpoint CTD00 belt & pulley #334506
    allan73
    Participant

    Re: Hotpoint CTD00 belt & pulley

    Sorry Martin, I was very busy this afternoon when I posted. I WILL search next time 😳

    October 28, 2010 at 7:35 am in reply to: Electrolux EW1200I #334059
    allan73
    Participant

    Re: Electrolux EW1200I

    If it is a hybrid timer, had a few of those with that fault.

    October 25, 2010 at 6:35 am in reply to: Hotpoint WT960p F01. #333744
    allan73
    Participant

    Re: Hotpoint WT960p F01.

    I could test the windings for the correct resistance with a multimeter I suppose, but I suspect it’s shorting when it’s in motion 😡

    October 23, 2010 at 6:28 pm in reply to: Hotpoint WT960p F01. #333742
    allan73
    Participant

    Re: Hotpoint WT960p F01.

    Don’t suppose there’s any way of bench testing these motors, with them being 3 phase ?

    October 23, 2010 at 12:29 pm in reply to: HOOVER T/D (TV 30 001) #333782
    allan73
    Participant

    Re: HOOVER T/D (TV 30 001)

    I’ve had the rear drum seal drop off & cause this problem on these.

    October 23, 2010 at 10:45 am in reply to: Hotpoint WT960p F01. #333740
    allan73
    Participant

    Re: Hotpoint WT960p F01.

    I’ve been told there are two 7 pin 3 phase motors for these, one with a 50mm stator & one with a 60mm.

    Does anyone know if they’re interchangeable ❓

    October 22, 2010 at 7:30 pm in reply to: Hotpoint WT960p F01. #333738
    allan73
    Participant

    Re: Hotpoint WT960p F01.

    Thanks.

    October 21, 2010 at 11:24 am in reply to: Indesit WIE137 F12. #332802
    allan73
    Participant

    Re: Indesit WIE137 F12.

    Just updating this, fitted main board from EMW yesterday and all seems well 🙂

    October 20, 2010 at 8:18 pm in reply to: Zanussi ZWF1427w E60 & E63. #333604
    allan73
    Participant

    Re: Zanussi ZWF1427w E60 & E63.

    Jeez, my eyes must be worse than I thought could have sworn it was E63 😕

    I think I’ll try a heater as it comes with the ntc and pray it’s not the board.

    Thanks Allan.

    October 20, 2010 at 8:38 am in reply to: Diplomat ADP8352 #333505
    allan73
    Participant

    Re: Diplomat ADP8352

    Thanks for the replies, are the wash pumps easy enough to change on the chinese built M/c’s ?

    October 18, 2010 at 10:37 am in reply to: Strange requests. #333274
    allan73
    Participant

    Re: Strange requests.

    A few years ago an old chap walked into what was our shop at the time and asked “do you do trips out ?”.
    I replied yes we do whats the problem your washer, dryer or oven ?
    ” I want to see the lights” he say’s. I’m starting to get a little puzzled now.
    “which lights have gone out, is it your washer?”.
    “Blackpool” he say’s ” I want to go to Blackpool”
    Anyway after much confusion it turns out many years before the shop was a sweet shop which ran regular excursions to the seaside 😆

    October 17, 2010 at 3:13 pm in reply to: hotpoint wmf740 #333193
    allan73
    Participant

    Re: hotpoint wmf740

    I think hotpoint do a kit now for these which does away with the need for the extension bit on the end of the valve, sorry don’t know pt number.

  • Author
    Posts
Viewing 15 posts - 286 through 300 (of 497 total)
1 2 3 … 19 20 21 … 32 33 34