Forum Replies Created
-
Posts
-
Re: SIMPLE PCB REPAIR TIPS
Hotpoint WMA models (with the board behind the facia)
Fault – All lights flashing
Change capacitor C6 400v 10ufRe: Bosch memory wipe
Proberbly correct if the user tried to operate the machine with the motor unplugged (Depending on the model), which would be registered as a fault
Re: LG227hsya
It would help if you got the model right is it a GWL227HSYA?
If so, PM me your email address and I’ll send you the manual
Re: Waste Carriers Licence
funkyboogy wrote:is this the same in scotland ?? – surely we can come up with some haggis type law .. will get the blower to my friend alex/
..lolHi Ally,
Here’s the page with the Scottish address on it:
Page with individual application addresses for England Ireland Scotland and Wales
Sorry it took so long, it completely slipped my mind.
George
Re: 1606 bearing changes
Are we still talking about the bearing change that you did in early February? If so, and you’ve used the correct bearing, I would say that it is near-on impossible to have a bearing become noisy that quick; unless of course you have nicked/damaged it during fitting.
Re: SIMPLE PCB REPAIR TIPS
On all of these errors/faults, check the capacitor C17 for domeing, remove & replace as necessary with 10v 680mf.
Indesit WIL, WIDL, IWM, IWME, possibly others too
Horizontal row of lights flashing
F09 Flash, OFF, OFF, Flash, eprom/setup errorHotpoint WF, WD, BWD and WT
Vertical row of lights flashing
F09 Flash, OFF, OFF, Flash, OFF, eprom/setup errorHotpoint WF, WD, BWD and WT & Indesit WIL, WIDL, IWM, IWME,
No power or lights litRe: **KNOWN ERROR CODES**
On all of these errors/faults, check the capacitor C17 for domeing, remove & replace as necessary with 10v 680mf.
Indesit WIL, WIDL, IWM, IWME, possibly others too
Horizontal row of lights flashing
F09 Flash, OFF, OFF, Flash, eprom/setup errorHotpoint WF, WD, BWD and WT
Vertical row of lights flashing
F09 Flash, OFF, OFF, Flash, OFF, eprom/setup errorHotpoint WF, WD, BWD and WT & Indesit WIL, WIDL, IWM, IWME,
No power or lights litRe: 1606 bearing changes
trotter wrote:Customer describes loud squeaking noise on drum rotation and really loud on the fast spin
If the squeeking is not the belt, it may well be the seal if it is either dilapidated or dry; take some silicone with you. The seal is usually easy to push into place with a flat object and the stale of a hammer.
trotter wrote:also the drum is not exactly central! How the hell do you get that front plate in the exact right position without the 3 legged tool as in the dvd? I spent ages trying to get it exactly right……seems I failed :-{
As for the front plate; you could remove the cast weights and tilt the machine backwards. The plate aligns without any problems this way.
Re: whirlpool SIOS discs
Re: Hotpoint washing machine – Ultima WMD960
When you say it is fine.. have you checked that the machine is heating ok?
Re: whirlpool adp4608
Sounds like you’ll need an engineer to attend to your wash motor
Re: hotpoint wmf 520
When you say it wont lock the door; is it even attempting… Is the control panel ok?
Re: AEG 16850 PNC 91460530903 still very wet after drying
Are you sure the correct inlet is charging and that it is not being supplied too much water?
Allsorts – Where Recycling Means Being NaturalSupporting http://www.findmyrecycler.co.uk – connecting waste to recyclers
We are looking for more recyclers
Get a FREE listing on the database – Contact Us at Find My RecyclerRe: Whirlpool W/M AWO/O 0 5526 Dead
You should have been looking for a faulty resistor not a capacitor
Allsorts – Where Recycling Means Being NaturalSupporting http://www.findmyrecycler.co.uk – connecting waste to recyclers
We are looking for more recyclers
Get a FREE listing on the database – Contact Us at Find My Recycler
