Andy jones

Forum Replies Created

Viewing 15 posts - 196 through 210 (of 1,462 total)
1 2 3 … 13 14 15 … 96 97 98
  • Author
    Posts
  • October 5, 2015 at 2:48 pm in reply to: Hotpoint tdc32 won’t stop turning #430741
    Andy jones
    Participant

    Re: Hotpoint tdc32 won’t stop turning

    Pull the knob off and make sure it isn’t cracked and on in the wrong position

    October 3, 2015 at 5:44 pm in reply to: Miele washing machine. Drum hits door seal #430661
    Andy jones
    Participant

    Re: Miele washing machine. Drum hits door seal

    With mine I suggested getting Miele out as I wasn’t happy fitting a new expensive seal without knowing the cause. Was hoping she would let me know the outcome.

    October 3, 2015 at 5:07 pm in reply to: Miele washing machine. Drum hits door seal #430659
    Andy jones
    Participant

    Re: Miele washing machine. Drum hits door seal

    I had a similar one where the nodule on the seal ended getting ripped off. Never did get to the bottom of it, like you said it’s a strange one

    October 3, 2015 at 1:28 pm in reply to: Old Hotpoint 6121 left side oven element. #430677
    Andy jones
    Participant

    Re: Old Hotpoint 6121 left side oven element.

    In stock with qualtex £16.14 trade

    October 2, 2015 at 5:11 pm in reply to: Cannon C60EKS #430665
    Andy jones
    Participant

    Re: Cannon C60EKS

    Not certain on that model no. Normally a couple screws at the back and you can lift slightly.
    The control panel may have to come off to remove it completely

    October 2, 2015 at 4:08 pm in reply to: Cannon C60EKS #430663
    Andy jones
    Participant

    Re: Cannon C60EKS

    On some the stat clips in to the selector switch. Would lift hob off and look, not too bad a job notmally

    September 30, 2015 at 7:02 pm in reply to: beko wmb91442 #430232
    Andy jones
    Participant

    Re: beko wmb91442

    Cheers dave

    September 30, 2015 at 4:06 pm in reply to: Bosch DW SMS69L02GB no heat #430617
    Andy jones
    Participant

    Re: Bosch DW SMS69L02GB no heat

    It’s a heat pump machine. Heater is an integral part of the was motor. Have replaced a few

    September 30, 2015 at 11:16 am in reply to: beko wmb91442 #430231
    Andy jones
    Participant

    Re: beko wmb91442

    Would you be able to send me the fault guide as well please. Have similar problem with same model. Cheers

    September 29, 2015 at 5:31 pm in reply to: Beko wmb91142lw #430527
    Andy jones
    Participant

    Re: Beko wmb91142lw

    Could you check that part no seamy. Doesn’t show anything on connect. Many thanks

    September 29, 2015 at 5:27 pm in reply to: Beko wmb91142lw #430526
    Andy jones
    Participant

    Re: Beko wmb91142lw

    Thanks seamy

    September 29, 2015 at 3:02 pm in reply to: Beko wmb91142lw #430524
    Andy jones
    Participant

    Re: Beko wmb91142lw

    Part no I fitted was 2827682081. Connect have done a pne check with Beko and they say it’s correct part.
    Can anyone confirm
    Cheers

    September 25, 2015 at 9:29 pm in reply to: Beko wmb91142lw #430523
    Andy jones
    Participant

    Re: Beko wmb91142lw

    Cheers Geoff. Will check

    September 25, 2015 at 6:30 pm in reply to: Beko wmb91142lw #430521
    Andy jones
    Participant

    Re: Beko wmb91142lw

    Will check them. Thanks simon

    September 25, 2015 at 3:12 pm in reply to: Zanussi not spinning after replacing brushes #430495
    Andy jones
    Participant

    Re: Zanussi not spinning after replacing brushes

    Grinding it back to the correct angle will cause a funny noise until they bed in. Always fit the correct ones

  • Author
    Posts
Viewing 15 posts - 196 through 210 (of 1,462 total)
1 2 3 … 13 14 15 … 96 97 98