Forum Replies Created
-
Posts
-
Re: Teka AL12-1200E – what is it?
Cheers Chris!!
I couldn’t make head nor tail of the customer’s description. Candy is no problem!Thanks again!!!
Steve.
Re: Ariston LS814 D/W
Every one I’ve seen with seal failure has been noisy or seized TBH. 😉
Steve.
Re: Ariston LS814 D/W
Most that I’ve seen had main wash pump seal failures – tip the machine back and the motor is caked in corrosion. The pump will leak badly when washing. It’s probably not a door leak; could be overfilling. Bet on the wash pump……… 😉
Steve.
Re: Competence U7101-4 – Bottom Oven Intermittent Failure
The “cut in” switches on the cabinet cooling fan. The “cut out” switches the oven off if the cut in doesn’t work and the cabinet overheats. 😉
You’ll need the fan cut in (or initiation) ‘stat.Hope that helps,
Steve.
Re: ise 555 intermittent no spin
Out of balance load? One or two heavy items will sometimes cause a no spin fault. Had one today!!!!
Steve.
Re: Beko WMA 765W Main Board please ?
Pressure bottle blocked by chance? That could possibly account for only functioning on high water level programs and lack of spin.
Steve.
Re: Alternative heater element for LG WM1375FHB
ELE9438 from Connect @ £6.05 + VAT. Hoover AC272 softwave element.
295mm long and 1800W. Very close……….. 😉Steve.
Re: Bosch sticking on cycle
These machines used to suffer from broken door wiring around the hinge top screw area – the loom would ‘melt’ into the bituminous soundproofing and snap the wires. Worth a look!! 😉
Steve.
Re: servis m6006w module
EMW are best for this – and 12 month warranty to boot. 😉 I don’t think Servis modules are interchangeable. If it’s not the problem return it to EMW. No stress….:D
Steve.
Re: Indesit Smart Card Reader
Tony, why don’t you post this info as a sticky at the top of this forum? It’s of interest to everyone. 😉
Steve.
Re: Electrolux EWD1409i washer drier.
I know how to access diagnostics, but I have looked at TDS and I can’t find a test program mentioned, only Demo mode. 😕
It is as if the main PCB is not configured, as the display board seems to work perfectly. And the door locks. There is only one main PCB available for this machine, but as I said, the type numbers and S/W version doesn’t match the original board.
The only option I have is to go back and try the diagnostics. Can you detail the test program setting please Mark?Cheers,
Steve.
Re: Electrolux EWD1409i washer drier.
Against my better judgement, I ordered the main PCB and the user interface (fascia PCB). TDS shows the user interface PCB (1321914754); the main PCB (973914601235000) was supplied configured. Also fitted new interlock unit (1249675131).
Just to recap on the original fault, the interlock was burnt and would chatter loudly, nothing else. No display. The main PCB was found to be blown in several places.
Fitted the new parts today and ‘Yes!!’ the program times show on the display. 😀 Then pressed the ‘Start’ button. The door interlock locks, and the Start LED keeps flashing………but the machine is dead. I have tried everything I can think of on this stupid machine and it still will not work. TDS offers no clues. My gut instinct was right all along!! 😈
The new main PCB is right in part number but the type numbers don’t match. The S/W version number is different too. Does that matter? All the plugs are keyed so getting them wrong is unlikely; I marked them as well to be sure. The interlock, and both PCB’s are new; all wiring is fine and in place………I’m foxed!!!!!! 😥One thing it has (very expensively) taught me is that Lux machines are as cr@p as Indesit. And I won’t be doing this again…..
Please…..any help or pointers greatly appreciated!!!!
Steve.
Re: Zanussi ZCE5000BK glass plate?
Firstly, the ceramic hob should be covered by your house insurance – obviously it’ll cost the excess, but where the ceramic top can be £250 + labour……. 😯
Contact your insurance company and they will guide you through getting it repaired professionally. Don’t buy anything until you have spoken to them.Hope that helps,
Steve.
