[bigsmokepiker]

Re: F&P Smartdrive 085 – error 00110010

If it is intermittently not going
IE Lights up ok but will not start your problem could be the Lid Switch
IE Reed Switch
This is a magnetic switch activated by magnet in lid
Common probem on these models
If it happens again advance to spin & try
If no action more than likely above
What can also happen if machine on spin & you lift lid it may not cut out.

Part # is 426457

[bigsmokepiker]

Re: F+P part wanted

I can help you out

[bigsmokepiker]

Re: Question on LG motors

Correct me if I,m wrong .Do you mean the Rotor

Direct drives dont have a pulley

[bigsmokepiker]

Re: F&P GW601-K secondary problem?!

If no power has to be motor controller
Pretty straight forward to fit /plug in type fittings

Motor controller does have fuse in it (Many have tried to just replace fuse only for it to blow again)
IF fuse is blown it has for a reason
1/Could be component on PCB(Motor Controller)

2/Could be faulty stator/Motor ETC

Check underneath machine for any signs of water leaks
a must on a machine of this age
With a blown out pcb (MC) have come across many instances in which
main shaft seal gives way /slow leak onto motor&or rotor postion sensor which in turn shorts out M/C

Mate if there are signs of leaks your RS

[bigsmokepiker]

Re: F&P GW601-K secondary problem?!

Display module Installation is straight forward Check plugs etc Power Supply OK?
If no power at all I can only say Motor controller
Have you tried it with your old display module

In your initial post it was suggested from diagnostics (Code 34)
Brake resistor fault
Primary source motor controller
Secoundary Source Display Module

[bigsmokepiker]

Re: Smart Drive 501 Problem

Rinse light on is a user warning error
When you enter diagnostics the last machine fault indicated will be
displayed as per IST post

[bigsmokepiker]

Re: Smart Drive 501 Problem

Indicates Fault code 104

Display to motor controller communications error
Can be display module or motor controller module fault
Generally the motor controller

You say inlet valves are shot (Both Hot & cold ?)
When you fill manually do you do this for wash cycle only?
Or both wash & rinse ?
Motor ControllerPART#425260p $200 Aus Display Part# 426033 $130

Cold valve P/N 426143 $45.00 Hot P/N426142$25.00
Best to also check under washer for any signs of leaking water

[bigsmokepiker]

Re: Smart drive 058 won’t start

Pump correct reading

[bigsmokepiker]

Re: Smart drive 058 won’t start

Best case then would be pump faulty

But more than likely M/C

[bigsmokepiker]

Re: F&P Smartdrive 508

Fault code(136) indicates Motor Stall Fault

The manual suggests to check
1 /Wiring harness Ie connections to motor Motor controller etc
2 Check free rotation of agitator & bowl by rotating by hand.Maybe bearings & seals are Seized)
Check rotor postion sensor(RPS)/motor Area for signs of water & corrosion
3 Motor controller fault.

Experience thou suggests Check under washer for signs of water leaks

Shaft seals give way and water leaks onto motor & RPS

If Looks Clear then RPS HAS BEEN Subject to Corrosive terminal problems.

[bigsmokepiker]

Re: Smart drive 058 won’t start

Are there any lights at all coming up when washer powered up ?

If not Could be 2 Things

1/Motor Controller
2/Pump On this model power runs thru drain pump if Pump is faulty then
washer will not power up

[bigsmokepiker]

Re: Difference between LG WT-H555TH & WF-T552TH washers

Re LG Service
We are a service agent for LG Whitegoods
LG Australia have got there act together
Parts are generally overnight
Technical help & support are first class
They are one of the better companys to deal with

As far as top load washers go /value for money there a pretty good unit

Parts Are cheap out of warranty & they are pretty easy to repair.

Personally I am a FRONTLOAD Fan (Miele )

The better units Miele($1700.000) AEG($1300.00)

[bigsmokepiker]

Re: Difference between LG WT-H555TH & WF-T552TH washers

WTH555TH Uses a direct drive motor system (similar to F&P Smart drives)No belts /pulleys etc
Less moving parts Motor is directly attached to the wash bowl .Wash action /bowl movement is generated by the motor actions

WFT552TH Uses a transmission system IE Gearbox /Wash action is generated by the reveresing action of motor (Pulley Belt) through the transmission

Personallyi feel the direct drive system is the better machine to go for

[bigsmokepiker]

Re: Fisher&Paykel MW059 washing machine won’t fill

Fault code indicates Hot Water inlet valve fault

Check connections to valve or Faulty valve

[bigsmokepiker]

Re: F & P SmartDrive 500 GW500B-K

Ist Code is pressure sensor fault
Check that pressure tube is intact(Clear tube that connects to motor controller/then runs down to outer bowl
This is your best case
Other than that faulty motor controller
2nd fault code indicates faulty display module

Also is the washer just not spinning IE Does it fill ,wash advance Etc

The machine will not spin until it pumps all the water

[Author]

Posts