[bigsmokepiker]

Re: F&P Smart Drive 708 stops at spin & beeps – R-H

Spin Led on is a user warning error
Most likely cause can be a blocked pump if it is not going onto spin

Washer must empty water out before it will move into spin cycle

[bigsmokepiker]

Re: Fisher & Paykel GW603-U Putting on Weird Performance

If During normal operation the spin light comes on this is a user fault Code

Spin light only flashing usually indicates Out of balance error

Could be OOB Switch fault ,blocked pump Or faulty pump, Suspension or Bias Spring

At What stage of cycle is this happening ?

Is it filling ,washing Etc ?

Does it pump out all the water

More info would be handy

Diagnostics as per Sticky post

[bigsmokepiker]

Re: Hoover Top Loader Washing Machine A6896

Part # 43143401 $15.00 AUD Plus POST

Can help if you PM

[bigsmokepiker]

Re: Fisher & Paykel Dishwasher 292T

This model is not a dishdrawer type
It is standard unit

[bigsmokepiker]

Re: Australian GW708 Motor-Controller earth connections

Wait for the seal Its not so much water getting into the OOB Switch
Its water getting into the motor controller

[bigsmokepiker]

Re: fisher & paykel BICT600E oven not baking.

To test element you,ll need a multi meter
Bottom Element is 1200 Watt( Reading 44 Ohm)
Element can be removed/Tested
Access is at rear of oven
If Element tests ok you May A problem with Function Switch(IE Cooking modeSwitch)

[bigsmokepiker]

Re: fisher & paykel BICT600E oven not baking.

There is no diagnostics on this model
Are you referring to Fan forced function?
Is the fan at rear of oven cavity working?
Id Check fan element (20-25Ohm)at rear of oven behind shroud Access thru front of oven Power off.Typically with F&P ovens this is the most common problem
If this is the case Part # 542653P

[bigsmokepiker]

Re: will my English fridge work in Australia ?

Aust Made & Imported fridges are generally made for T Class Climate

Your Frig will work oK IE Same voltage Etc

The only problems you may experience is sweating around the cabinet area .(the frig that is)

[bigsmokepiker]

Re: FISHER PAYKELL tech info

Model # of Dishwasher?

[bigsmokepiker]

Re: Fisher & Paykel Dishwasher 292T

OK Drain pump always comes on at start of any cycle
But if no water coming it could be inlet valve or in some cases I have had problems with main power PCB (Located down bottom behnind kick panel)
If you can hang 5 i do have some diagnostics but i will have to post later this arvo when i get access
Regards

[bigsmokepiker]

Re: Hoover 1010

Is This a top load washer
Hoover made a 1010 Washer In Aust

[bigsmokepiker]

Re: Fisher & Paykel gw708 motor problem ?

Yep thats right for phase 1-3
GW708 is A Phase 4 Washer

Motor controller is yellow in color? Phase 4 Size Setting

Or if Green in color is Phase 3 Phase 1-3 Size setting

Hence maybe the confusion

[bigsmokepiker]

Re: GW700 stops while washing and beeps

Fault code 130
Likely cause can be Rotor position Sensor(RPS)
Can be corroded contacts On RPS
You will have to check underneath washer for any signs of water leakage
A washer of this age can have main seal problems (IE Water leaks slowly from main shaft eventually finding its way to the Motor area where RPS is situated)
If this is the case time for a new washer.

Second cause can be a faulty motor controller
New Controller comes as kit Part# 425243KIT $240.00AUD

Best case is if it is just a faulty RPS Part # 420296 $50.00

[bigsmokepiker]

Re: SmartDrive 503 error Code 1101

Just Double Checking Fault Code
00001011 Fault code 11 Pressure Sensor Fault

00001101 Fault Code 13 Pump Fault

[bigsmokepiker]

Re: Fisher & Paykel gw708 motor problem ?

Code 9 is Size setting
To set as Per Penguin post
Why did you change in first place?
Is It a New controller?
Is it right Part ?
When you changed controller did the washer have water in the bowl?
In some cases when changing motor controller & there was water in bowl
you may have to blow through pressure tube to clear.

Hope this helps

[Author]

Posts