Forum Replies Created
-
Posts
-
Re: F&P 703 stops & starts on refill. Code 136?
fault code 136 suggests motor stall -Motor controller has been unble to start motor
Possible causes
Faulty motor controller
Faulty Rotor position sensor(RPS)
Seized bearings & seals
First thing to check would be any signs of water leaks under washer near the motor area
What can happen is seal gives way & leaks onto Rotor positon sensor(which is housed in the motor)RPS Connections corrode & commonly give this error
IF you have noticed any bearing failure type noises then i would suggest this could be the caseRe: Miele W828 error code
More than likely worn motor brushes
Or it could be motor connections wiring harness faultBut i would look at motor brushes First
Re: Fisher and Paykel Smartdrive 500 tub springs
Yep only one spring (Bias Spring)keeps away from Out Balance Switch
It has Four Tub Suspension Rods &springs (1 Each Corner)
Re: Fisher & Paykel Smart Drive 058 Lights on but won’t
Looks likely to be a faulty lid switch(Magnetic Reed Switch)
Re: f & p 708 stops and turns off during cycle
From your intial post when you say it stops are you referring to no lights on washer?If this is the case more than likely the pump is overheating .(they have an internal overload) Power to Controller runs thru pump.
That can be the reason why machine will start up again after being switched off for a while (IE Pump cools Down )
Check to see how hot pump gets you may also see signs of rusting on Pump
Power OFF
Re: Fisher Paykel 703 error code 00110010
Sound like Motor Controller
My Apologies i didnt read post correctly
Re: Fisher Paykel 703 error code 00110010
Fault Code 50
00110010 (0/0/32/16/0/0/2/0)Fault code relates to faulty hot inlet valve
(by your post Inlet valve diaphram staying open)
Would suggest chaning hot valve Part # 426142p $25.00AUDRe: Panasonic Microwave Door E required
Pana Australia have them
Part # A302K6000BP Door E NN-D851
Cost $130.00 AUD Post $16.50AUD
Can Get If You LikeRe: Fisher & Paykel Smart Washer 601 repeats wash cycle
Washer is in recycle feature
To turn off
Turn power at power point. Press &hold Wash temp down button & then power button release buttons after 2 short beeps.
Now Use water level up button to turn recycle feature on/offMed water level LED ON = Recycle ON
Med water level LED OFF= Recycle OFFRecycle status can be checked when you Ist turn on washer
If last 3 lights come on =recycle ON
if last 3 lights Off =recycle OFFRe: No spin…??
Does the timer actually advance tospin & advance through the spin cycle?
When it should be in spin is it the agitator that is moving rather than spin bowl?
If agitator is moving is it just spinning in one direction or is it reverseing back & forth
Full model would be handyIf it is washing on spin
It can relate to the timer ,Brake arm ,Spin solonoid Or the transmissionRe: F & P Smartdrive 058 Issues
When you checked pressure did you make sure that you pumped all the water out. Pressure tube runs from motor controller down to outer bowl
Motor controller Part # 426204P $220.00audRe: Fisher & Paykel IW709 Fault Code 37
Fault code 37 Primary source relates to a pump blockage
Secondary may a blocked or kinked pressure tube
Thirdly can relate to motor controllerNow the status i presume is after putting into diagnostics ?
In which case it indicates a faulty lid Switch(located Under Hob ON the RHS)To test OOB Switch open lid & move bowl to back RHS Corner Status should change at this Instance
From your post are you saying the washer powers up but no action at all when cycle selected & start pressed . If this is the case i would suggest lid Switch
