Forum Replies Created
-
Posts
-
Re: F&P GW601-K error code – help!!
Can you feel the start button clicking on/off
The other buttons give the same contact as Start/pause Button
It is very common that this buttons do lose there contact
If you cant feel a definite clicking then your possibly up for a display module
Fault code indicates Brake resistor fault
Circuit that controls braking of motor is faulty
Could be Motor controller fault Or Display module FaultMotor Controller Part #426260p$220.00 Aus
Display Module Part#426033p $135.0AusRe: F&P GW601-K error code – help!!
Can you feel the start button clicking on/off
The other buttons give the same contact as Start/pause Button
It is very common that this buttons do lose there contact
If you cant feel a definite clicking then your possibly up for a display module
Fault code indicates Brake resistor fault
Circuit that controls braking of motor is faulty
Could be Motor controller fault Or Display module FaultMotor Controller Part #426260p$220.00 Aus
Display Module Part#426033p $135.0AusRe: Fisher & Paykel SmartDrive 058, fills slow then erro
Cold Valve Is Part# 426143 $44.00 Aus
Hot valve Is Part #426142 $24.00 AusRe: Fisher & Paykel gw708F Error code
Error code indicates blocked or faulty drain pump
PUMP is mounted under bowl
Power off & PLUG OUT!!!!!
Turn fan at end of pump to seee it it moves freely
In some cases this may also free it anything stuck in there
Failing that you may have to remove pumpRe: F & P SmartDrive 500 GW500B-K
OK Bad news
Ist Fault code 00000100 communication error
Motor control fault
Can try turning on/off at wall but if faults again
Likely source motor controller
00010000 Display/motor controller out of sequenceLook if it needs motor controller for this older model scrap him
Re: F & P SmartDrive 500 GW500B-K
00010000 Indicates Display/Motor controller out of sequence
Turn washer off at wall and on again after 10orso sec
Restart washer
If fault appears again have disable restart feature
Enter diagnostics washtempdown/power Use water level down button to turn restart on/off
Low water level indicator off=restart off
Low ”” ”’ ”” on=restart onRetest a new fault code should come up
Note washer will not spin until water pumped out
Pump is under washer bowl Power off if you fidddle with thisRe: F & P SmartDrive 500 GW500B-K
Fault code indicates water loss(Leak)
IE The motor controller has needed to top up water level more than 4 times.
Cause can been from siphoning Check drain hose height
Other cause /check for leaks underneath washer around pump& shaft area
In some cases it may be faulty motor controller (Main PCB)Re: Fisher&Paykel MW059 washing machine won’t fill
Fault code indicates faulty cold water inlet valve
In some cases a faulty valve can take out Motor controller(main PCB)AS WellRe: F & P Smartdruve 058 solenoids repeatedly turning of
fault code indicates motor stall error
Possible causes
Faulty motor controller(main PCB )Most probable
Wiring harness break
Seized bearings
Or FaultyRPS(Rotor postion sensor)
Check under washer for leaks If there are signs of leaking water
then trouble
IE Main seals /bearings main shaft RPS & possible motor controller(lots$$$)Re: LG GR359SQ any help please ?? and thanks in advance
Hang in might be able to help
We dont have this model here but more than likely
similar to GR349SQ (Which we have In Aus)
Going to hold of diagnostics for
Meanwhile is the evaporator icing up?
IE Coils in Freezer
If so it may not be going onto defrost(Ice bulid up restricts airflow)Re: F & P 501 Problem!!
Last fault code indicates RPS(Rotor postion sensor)
But typical of this model may be Motor controler.
Also with 501 ( 9-10 Year Old) I would check underneath machine
for signs of leaks
What can happen ? Seal gives way & leak onto to motor area ( Where RPS Is located ) Water can corrode contacts at RPS .Giving this fault Code. If So New Machine ( IE Means , Main Seal Bearings Main Shaft, RPS, Maybe Stator
Best Case RPS ( $45_ $50 Aus)
