cab

Forum Replies Created

Viewing 15 posts - 376 through 390 (of 423 total)
  • Author
    Posts
  • in reply to: kenwood dishwasher kw24fi/b #188345
    cab
    Participant

    Re: kenwood dishwasher kw24fi/b

    all 7 lit is door, will show this when you open door, if it is faulting with 1 minute gone try looking to see what lights flashing before opening door. this is chinese haier fault codes in the `know codes` thread.

    cab

    in reply to: AEG configuration code #188364
    cab
    Participant

    Re: AEG configuration code

    SENT VIA PRIVATE MESSAGE BOX

    cab

    in reply to: Zanussi Sticking #188380
    cab
    Participant

    Re: Zanussi Sticking

    seems like you are heading in the right direction, but is the machine syphon by itself so the machine water level never reachs level on rinse?

    cab

    in reply to: Zanussi modules #188387
    cab
    Participant

    Re: Zanussi modules

    hi the 3 boards supercede each other 0092 is latest one, they arnt interchangable with zwf different electronic control only one board behind facia they com preconfigured.

    cab

    in reply to: Whirlpool AWM6145/3 #188271
    cab
    Participant

    Re: Whirlpool AWM6145/3

    hi think I have had a similar problem that turned out to be only the motor brushes.

    cab

    in reply to: aeg door problem #187754
    cab
    Participant

    Re: aeg door problem

    hi yep door hook can wear and spring looses tension suspect parts would be obsolete. Started manufacture in 1982!

    cab

    in reply to: Zanussi drum paddles #187708
    cab
    Participant

    Re: Zanussi drum paddles

    Hi I have had them come out and look intact, easy to refit, look at the drum, there are 6 keyed slots (3 on each side) the paddle fits into, in the middle is a piece of the drum which should be bent upward, when the paddle is positioned and pushed back this `tang` locks the paddle in place.

    cab 😆

    in reply to: Beeping Zanussi #187613
    cab
    Participant

    Re: Beeping Zanussi

    Johnnyboy, replied to other thred on this machine

    cab

    in reply to: AEG washing m/c soap box motor. #187659
    cab
    Participant

    Re: AEG washing m/c soap box motor.

    hi its the water distributer, electrically driven on these, dont no if they can me repaired, have previously only replaced. not difficult to do, though havent done one in a while, there are two different part numbers depending on product number

    in reply to: Electrolux Configuration Codes #187654
    cab
    Participant

    Re: Electrolux Configuration Codes

    hi the codes are on tds look on the electrical parts and scroll down item number 990 AE1C101AA137022C
    NUMBER SHOULD ALSO BE ON A STICKER O ORIGINAL MODULE IF STILL ON MACHINE

    cab

    in reply to: Zanussi FX1465W – 914792705/00 Washing machine error #186959
    cab
    Participant

    Re: Zanussi FX1465W – 914792705/00 Washing machine error

    Hi the end light flashes to give you the 1st figure of the code, the start/pause flashes at same time to give the second, but five flashes is code E50 something! which is motor related. press sart/pause & stop/skip buttons together for about 2 secs and read code, but the only thing left is motor or wiring

    cab

    in reply to: Electrolux ESL6114 d/w #187100
    cab
    Participant

    Re: Electrolux ESL6114 d/w

    ok

    in reply to: Electrolux ESL6114 d/w #187098
    cab
    Participant

    Re: Electrolux ESL6114 d/w

    penguin, did you get the email I sentwith the service bullitin on?

    in reply to: Electrolux ESL6114 d/w #187096
    cab
    Participant

    Re: Electrolux ESL6114 d/w

    iwms Inegrated Water Management System- the side tank!

    cab

    in reply to: Lux ER2656B F/F evaporating tray #187425
    cab
    Participant

    Re: Lux ER2656B F/F evaporating tray

    I have a service bulletin on defrost trays for different compressors may be of use, email me and I will send it to you.

    cab

Viewing 15 posts - 376 through 390 (of 423 total)