Criscold

Forum Replies Created

Viewing 15 posts - 571 through 585 (of 816 total)
1 2 3 … 38 39 40 … 53 54 55
  • Author
    Posts
  • October 12, 2011 at 5:58 pm in reply to: zanusi zx99/5si need tech info please #361283
    Criscold
    Participant

    Re: zanusi zx99/5si need tech info please

    Let me have your email

    Colin

    October 12, 2011 at 3:42 pm in reply to: Indesit Model Number #361267
    Criscold
    Participant

    Re: Indesit Model Number

    I think it may be IS70C as this has a comercial code of 30617
    Belt size 19916PHE
    C00116358

    Colin

    October 12, 2011 at 3:34 pm in reply to: WM64 Not heating water #361256
    Criscold
    Participant

    Re: WM64 Not heating water

    Have you checked thermistor ?
    Resistance @ 30 C = 9.8 K ohms ; @ 85 C = 1.7 K ohms

    October 12, 2011 at 3:19 pm in reply to: zdt6252 #361258
    Criscold
    Participant

    Re: zdt6252

    Very simple job on this one, I normally lay the machine on the RH side – Remove plastic cover at bottom rear and then remove the metal plate that holds the motor in place along with the motor plug, You will find a plastic clip on the underside of the housing release and pull motor assy thru back

    October 11, 2011 at 6:33 pm in reply to: Hotpoint BFI620 Door seal #361094
    Criscold
    Participant

    Re: Hotpoint BFI620 Door seal

    Did a search for BFI seal and found this, don’t know if correct one C00056475

    Colin

    October 10, 2011 at 1:12 pm in reply to: Servis / Hygenna APM 6852 ? #360967
    Criscold
    Participant

    Re: Servis / Hygenna APM 6852 ?

    Check this
    http://www.apart4u.co.uk/news/diagrams/ … sted-below

    October 10, 2011 at 1:07 pm in reply to: Servis / Hygenna APM 6852 ? #360966
    Criscold
    Participant

    Re: Servis / Hygenna APM 6852 ?

    Yes simple mod req & will try to find sheet for you

    Colin

    October 9, 2011 at 8:55 am in reply to: Electrolux ESI 6220 diswasher #360885
    Criscold
    Participant

    Re: Electrolux ESI 6220 diswasher

    Several versions of this machine – Have you got Product number

    October 8, 2011 at 5:59 pm in reply to: Belling XOU288 BR double oven fan motor required #360861
    Criscold
    Participant

    Re: Belling XOU288 BR double oven fan motor required

    Just been clearing my workshop out and found a MTR142

    Colin

    October 8, 2011 at 12:22 pm in reply to: Ariston A1636 top light flashing #360867
    Criscold
    Participant

    Re: Ariston A1636 top light flashing

    I think this is error F07 – Heater relay stuck – could also be caused by pressure switch sticking

    Colin

    October 5, 2011 at 5:36 pm in reply to: tricity bendix dh 103 #360688
    Criscold
    Participant

    Re: tricity bendix dh 103

    Looks like only the one stat on this one, when machine reaches temperature this would switch timer to advance off of the heat setting. Have you checked cables in base of the door and I presume the motor is running. Let me have your email if you req diagrams etc.

    Colin

    October 5, 2011 at 1:43 pm in reply to: Connect Prices #359766
    Criscold
    Participant

    Re: Connect Prices

    Just had a customer requesting a new control panel moulding for his Electrolux Dishwasher – pt no. 1560647206 – Connect price £704.74 + vat

    October 4, 2011 at 9:28 pm in reply to: Bearings for Zanussi ZWF1227W #360616
    Criscold
    Participant

    Re: Bearings for Zanussi ZWF1227W

    As long as not sealed drum

    6305 Bearing
    6306 Bearing
    1249667013 Seal

    Connect BRG9109
    Qualtex QUABKT84

    October 3, 2011 at 3:59 pm in reply to: beko wma745 #360425
    Criscold
    Participant

    Re: beko wma745

    Have you tried test mode on this to check error codes ?

    Colin

    October 3, 2011 at 3:32 pm in reply to: Electolux D/W ESL424 #360414
    Criscold
    Participant

    Re: Electolux D/W ESL424

    This machine is probably 10 years old and think that the first thing I would check for would be the circ motor stuck, used to do a load where the seals had leaked into the front bearing

  • Author
    Posts
Viewing 15 posts - 571 through 585 (of 816 total)
1 2 3 … 38 39 40 … 53 54 55