Criscold

Forum Replies Created

Viewing 15 posts - 631 through 645 (of 816 total)
1 2 3 … 42 43 44 … 53 54 55
  • Author
    Posts
  • July 29, 2011 at 9:44 pm in reply to: Zanussi TC7103w 916093530 Wont start #356451
    Criscold
    Participant

    Re: Zanussi TC7103w 916093530 Wont start

    Looking at the drawings it appears that this machine has a switch called a box switch located at the front near the steam exchanger. This switch is on the neutral line before the door lock & start solenoid – worth a check & the flap and steam exchanger
    If you need drawing – let me know

    Colin

    July 29, 2011 at 3:46 pm in reply to: jlwm 1203 sticking at one minute #356366
    Criscold
    Participant

    Re: jlwm 1203 sticking at one minute

    I can send you some info on the machine for diagnostics if it would help

    Colin

    July 28, 2011 at 5:14 pm in reply to: AEG L12830 Washing Machine -Starts then stops #356387
    Criscold
    Participant

    Re: AEG L12830 Washing Machine -Starts then stops

    I think you need to run diagnostics, let me have your email if you req info.

    Colin

    July 28, 2011 at 3:11 pm in reply to: Zanussi ZWF1421W (914225203/03) washing machine fault #356361
    Criscold
    Participant

    Re: Zanussi ZWF1421W (914225203/03) washing machine fault

    Can you get into diagnostics ?

    July 26, 2011 at 4:43 pm in reply to: ZWD16270WI Not Starting #356247
    Criscold
    Participant

    Re: ZWD16270WI Not Starting

    No thats the dryer module, inverter board in base of machine

    July 26, 2011 at 3:12 pm in reply to: ZWD16270WI Not Starting #356243
    Criscold
    Participant

    Re: ZWD16270WI Not Starting

    You may have to go into diagnostics to get correct code

    July 26, 2011 at 2:55 pm in reply to: Beko WMC61 #356238
    Criscold
    Participant

    Re: Beko WMC61

    Have you tried entering diagnostics

    July 26, 2011 at 8:15 am in reply to: Smeg Hood KSEIV950X #356192
    Criscold
    Participant

    Re: Smeg Hood KSEIV950X

    Thanks for that, I was hoping it would be something like that but didn’t want to force anything. it may just be a power supply fault as customer unable to find where the power connection/switch is located

    Colin

    July 25, 2011 at 5:28 pm in reply to: Zanussi FJS1025W error – HELP! #356184
    Criscold
    Participant

    Re: Zanussi FJS1025W error – HELP!

    I can only think of the usual earth faults ie Motor, heater.
    Have you tried entering diagnostic ?

    Colin

    July 25, 2011 at 7:22 am in reply to: JL WM1407 #356166
    Criscold
    Participant

    Re: JL WM1407

    You have mail

    July 23, 2011 at 4:30 pm in reply to: JLWD 1480 914603110 00 #356070
    Criscold
    Participant

    Re: JLWD 1480 914603110 00

    This machine has a separate selector switch – could be that or knob, let me have your email if you require manual

    Colin

    July 22, 2011 at 4:02 pm in reply to: zannusi t/d keeps knocking off #356016
    Criscold
    Participant

    Re: zannusi t/d keeps knocking off

    I agree – Control Board 135.00

    July 21, 2011 at 2:35 pm in reply to: AEG L63742VI Fault #355966
    Criscold
    Participant

    Re: AEG L63742VI Fault

    Let me have your email and can send you a pdf

    July 21, 2011 at 1:40 pm in reply to: Beko WM8127S #355940
    Criscold
    Participant

    Re: Beko WM8127S

    You should have mail

    July 21, 2011 at 12:58 pm in reply to: Beko WM8127S #355938
    Criscold
    Participant

    Re: Beko WM8127S

    I don’t know this machine,This may be a silly question & I know you say you tested everything but could the 2 be an error code
    error 2 = heater o/c. If you need test info let me know

    Colin

  • Author
    Posts
Viewing 15 posts - 631 through 645 (of 816 total)
1 2 3 … 42 43 44 … 53 54 55