eastlmark

Forum Replies Created

Viewing 15 posts - 2,086 through 2,100 (of 4,480 total)
  • Author
    Posts
  • in reply to: smeg dishwasher error #275451
    eastlmark
    Moderator

    Re: smeg dishwasher error

    Its not an error code as such but may be worth re-setting and starting agian. Hold in the start button for 5 seconds or so and see if you can select a different program.

    eastlmark
    Moderator

    Re: Neff model W4380X – liquid left in conditioner compartme

    assuming you have had the draw out and cleaned the syphon cap in the fab con compartment then the problem will be a lack of water reaching the compartment. Check the holes in the section of the dispenser top that spray into this compartment are clear. It is possible to carefully lever down the centre section with 2 small slotted screwdrivers to gain access inside to clean it out properly. If this doesnt work then it will require a new dispenser top section.
    You need to post a full and correct model number for any further assistance.

    in reply to: Hotpoint WD440 dead #275402
    eastlmark
    Moderator

    Re: Hotpoint WD440 dead

    what happens when you plug your hardware key in Martin?

    in reply to: Smeg/homeserve #267713
    eastlmark
    Moderator

    Re: Smeg/homeserve

    Just had our spares discount knocked down from 45{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} to 40{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}. They say its across the board, same for everyone, Is that true?
    Price increase also from Feb 1st…..expected that one and must admit they dont raise their prices yearly, or even more frequntly, as everyone else seems to do.

    in reply to: on / off switch for Hoover tumble Drier #275230
    eastlmark
    Moderator

    Re: on / off switch for Hoover tumble Drier

    think you need the relay pcb that is just behind the facia but not quite as easy as it looks to change.

    in reply to: SMEG DI409C #275093
    eastlmark
    Moderator

    Re: SMEG DI409C

    dont see too many of these so cannot say if its common or not. Sometimes get leaks through the door latch slot which get on the door microswitch, usually door damage or hinge problem but can sometimes be solved by tightening up the door latch to make the door close tighter.

    in reply to: 08/09-Football Season.. #254919
    eastlmark
    Moderator

    Re: 08/09-Football Season

    iadom wrote:8) 😀 😛 United stroll through with only four first team players on show. 😆

    Ronaldo..Tevez…. yeah, agree a weak line up fielded.


    still some of us need to concentrate on our League position and of course the Important Carling Cup.

    in reply to: SMEG DI409C #275091
    eastlmark
    Moderator

    Re: SMEG DI409C

    Think you need to visit it and record the error code, as Its after 10 mins then maybe a heater fault?

    in reply to: Smeg Fridge Freezer S30STRP Door Hinge #275106
    eastlmark
    Moderator

    Re: Smeg Fridge Freezer S30STRP Door Hinge

    really need the FAB number to correctly id this part but 681330639 and 611330764 fits most AFAIK but it may depend on which way the door is hinged

    in reply to: Bosch/Siemens brushes nightmare #275174
    eastlmark
    Moderator

    Re: Bosch/Siemens brushes nightmare

    Strange, I do plenty of these a week and never had a problem…..always use genuine though……obviously worth it.

    in reply to: best toolboxes? #275111
    eastlmark
    Moderator

    Re: best toolboxes?

    find soft bags much more comfortable, especially with a shoulder strap.

    in reply to: The Stig #234280
    eastlmark
    Moderator

    Re: The Stig

    eastlmark wrote:Believe me, for a fact I know it is Ben Collins.


    😉

    in reply to: hygena 8102/1 #274938
    eastlmark
    Moderator

    Re: hygena 8102/1

    would suggest maybe a lack of water? That one has a filter that the customer never takes out to clean as the handle lifts off leaving the main filter still in place, could just be that.

    in reply to: BDW060?? #274945
    eastlmark
    Moderator

    Re: BDW060??

    Penguin45 wrote:Cookers brand – Brandt made. Pump will be a vertically positioned twist fit on the right hand side from the front. You’re going to have to pull it out.

    Chris.

    ….retained by a torx screw that is in an impossible position to undo! Dont try to twist the pump off before getting it out, somehow.

    in reply to: Whirlpool top loader Drive coupling #274797
    eastlmark
    Moderator

    Re: Whirlpool top loader Drive coupling

    Pat-UK wrote:I don’t suppose anyone has one lying around gathering dust or on the shelf they wanna sell to me.

    Many Thanks

    Pat
    why, is there a shortage?

Viewing 15 posts - 2,086 through 2,100 (of 4,480 total)