[eastlmark]

Re: Hoover HNWF 6135-80 NTC Reading

Temperature Ohmic Values for drier NTC
(°C)
(Ω)

25 ~ 48500
140 ~ 1044

and for wash NTC
Temperature
(°C)
Ohmic Values
(Ω)
25 19500
30 15760
35 12825
40 10506
45 8660
50 7181
55 5989
60 5022
65 4233
70 3586
75 3053
80 2610
85 2242
90 1933
95 1674

as usual the format completely changes from what I acutualy posted 😳
I guess you get the idea, first figure is temp, second is value in ohms. cold water will be around 30K at a guess. about what you have quoted in you post.

[eastlmark]

Re: Football Season 2010/11

yep, shame I wasnt watching by then 😳
A respectable result in the end. 😆

[eastlmark]

Re: Fagor FUS-3611IT no drain pump on dryer cycle?

How long have you left it before deciding its not coming on? Pretty sure I had one of these and it was like 15 minutes before valve and pump are energised.

[eastlmark]

Re: Football Season 2010/11

someone remind me never to buy a Pirelli tyre ever again. 👿

[eastlmark]

Re: smeg wdi 12c

and E6 is a slow drain fault, 5p in the pump outlet or a blocked air bell.

[eastlmark]

Re: Smeg ST1123 dishwasher.

if it has one it will be part of the air break in the right hand side, never known one to fail though and as there is a specific error code for a flow meter failure then I doubt it is the cause.

[eastlmark]

Re: 20rud3j wpool american

ok Eddie, I stand corrected, should have looked up the model, I know…

[eastlmark]

Re: 20rud3j wpool american

or buy a capacitor and relay kit for peanuts!

[eastlmark]

Re: Whirlpool Oven AKZ161/IX/02, 858516115090

AFAIK, the board is not configured but is done so by cutting out links as per the instructions supplied guided by a mysterious number that is quoted on the rating plate…..the one I did recently did not have any such number so I took a wild guess….and it worked and no recall so far.
these are horrible ovens! Expect the word STOP as soon as you re connect the power which may or may not dissapear by fiddling with the buttons.

I had the same fault as you, power board was the culprit but I had changed the ntc first with no result but left it in anyway.

[eastlmark]

Re: Smeg ST1123 dishwasher.

part number is 696290833 for pcb. assume you have checked everything you said i dont think it could be anything else. Very slight earth faults on the circ pump can cause problems like this so make sure that all is ok down there.

[eastlmark]

Re: bbc watchdog

Martin wrote:Clive Bramell (a.k.a. Oxford & Abingdon Washing Machine Repairs)
10 Longfellow Drive, ABINGDON, Oxon, OX14 5PQ Tel: 01235 520071

Named and shamed……!!!

He does exist then? I found this so cliche’d I began to think it may have been actors and the whole thing staged for the sake of “good” tv.

[eastlmark]

Re: bbc watchdog

allan73 wrote:I cleaned someones sump out yesterday on a WMA Hotpoint for £30 am I too cheap ?

Allan (effectively a one man band).

yes!

[eastlmark]

Re: bbc watchdog

the cowboy who cleared the other womans pump for £30 did our trade just as much damage as the moustchiod sleaze bag himself.

[eastlmark]

Re: Neff T1722NO/02 element.

now replaced by 644726 not what you want to know but…why not read what is says on the old one and get your tape measure out? 😆

[eastlmark]

Re: bbc watchdog

I would have loved to see him change a pcb, smart card programming etc, now that would have been a laugh.

[Author]

Posts