[electrofix]

Re: Canon CH60 DPXFs tripping main RCD

tripping RCD faults are normally down to element faults. if your grill works ok then that element is eliminated
on most top ovens there is a second element under the floor of the oven and I suspect this element (should be part no C00230135 on yours) has an earth fault when it gets hot
cant think why he changed the potentiometer unless he thought is was getting too hot

Dave

[electrofix]

Re: Bosch SGS43C02GB/35 Classix control unit Programming

try telling us the Enr number and your problem

setup instruction normally come with new timer and are just for initial setup. one set it does not need changing

Dave

[electrofix]

Re: Siemens HB15N550GB/03

have checked the board I have and the relays used are

HF152F 9 volt coil and
HF3FD 9 volt coil

HF152F is a similar size but they seem to have slightly different pin positions to the shrack 3-1415356-1 / PBH34009
if you think you can alter the board to fit it your welcome to one. board has come out of a Neff oven unit so is used in a similar way (part no 658000)

Dave

[electrofix]

Re: Bosch Exxcel SRS45E38GB/09 Does Not Start Wash Cycle

the base of the dishwasher is a tank that catches water that leaks ( if any) this tank has a float that stop the programme and turns on the pump till the water is removed

Dave

[electrofix]

Re: Siemens HB15N550GB/03

have a scrap board in the van will have a look to see if that one of them

Dave

[electrofix]

Re: VT1014D23 – runs for 4 seconds at a thim

difficult no easy way to be sure 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} but is sounds like the board power supply is acting up
you could contact EMW electronics or http://www.qer.biz/servreps.htm
and see if they can test and repair this board.
another problem that we are getting these days is unprogrammed boards so if you buy a new one its useless unless you have the gear to programme it

Dave

[electrofix]

Re: VT1014D23 – runs for 4 seconds at a thim

no sounds more like a board problem

Dave

[electrofix]

Re: Siemens HB15N550GB/03

the power supply is just to supply power to the pcb so a short in an element to earth is not going to affect this board unless the main board gets damaged too.
had a similar bosch board go faulty and if you looked carefully you could see a hole in one of the driver chips and that was all

you should be able to verify the voltages on the power board are ok

Dave

[electrofix]

Re: AEG F34502V10 over filling

not sure what info you have but have pm’ed some to you

Dave

[electrofix]

Re: Tecnik TKL925 burning smell after new brushes

I would expect an electrical sparking smell as brushes bed in but any other smell is suspect
when you fit new brushes it is a good idea to do lighter loads and lower the final spin speed for about the first 10 washes

Dave

[electrofix]

Re: Bauknecht WA 821 washing machine doesn’t spin

short answer from me in no

but the drum only seems to be turning one way i would expect machine to turn both ways to distribute load. does it reverse in the wash programme ?

Dave

[electrofix]

Re: beko dcu 7230

element has an overheat stat that may have tripped

sent you some info by pm

Dave

[electrofix]

Re: Help finding replacement lower basket Beko DW450

part number is 1799700800

its not the sort of part you can get easily as its not a fast moving part. all my suppliers are showing special order which means they would rely on Beko

have you looked on ebay for a good second hand one ?

Dave

[electrofix]

Re: ZDC68560W E00 error code

the only ref to E00 is when you clear the alarm

have sent you the tech info see if it helps

Dave

[electrofix]

Re: Beko WMA 520S motor brushes

glad to help m8

Dave

[Author]

Posts