[electrofix]

Re: Hoover VHV180 blowing cold air

can be the timer switch there is contact that turns the heat off 10 mins from the end

Dave

[electrofix]

Re: Bosch Classixx "Check Water" fixed then keeps happening

if tipping cures it there is water in the base under the wash area. there is a float in this base to detect leaks and shut the unit down if it detects one.

Dave

[electrofix]

Re: LG F1480YD5 – Wash Element support

had a really good look on connect and could not see anything even on similar models. if you type in ” LG heater support” you get lots but no pictures and no models

Dave

[electrofix]

Re: LG F1480YD5 – Wash Element support

have you checked the sump hose dont know with LG but some of them are just a bent bit of wire small enough to land in the sump hose

Dave

[electrofix]

Re: Bosch WAE24366GB

there is a whole post on this at the top of the forum but top of the list is heater

Dave

[electrofix]

Re: beko dcu 7230

if its getting too hot there is not much it can be

there a 2 thermistors. 1 is part of the element the other is at the front by the filter

other than that is airflow or board

will pm some info

Dave

[electrofix]

Re: LG F1480YD5 – Wash Element support

cant see any support on diagson connect even looked a drum pictures but cant see anything

is the spider ok ?

Dave

[electrofix]

Re: Zanussi ZWF 1632 W control panel ‘dead’

its going to be a control card issue. may just be the cable between both cards but till you get someone who is qualified to check you will not know

Dave

[electrofix]

Re: Smeg Int’ DW (DI 612 CA) no heat

from what i can remember Smeg can throw up random fault codes if the soap draw solenoid is faulty
search the site its around somewhere

Dave

[electrofix]

Re: Beko WMA 520S motor brushes

gen part number 371201202

try here in the site shop

https://shop.ukwhitegoods.co.uk/catalog … =371201202

but beware although Beko list this number for this machine you can never be 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} certain till you see them

you can see the brushes by leaning the machine backwards and looking underneath but make sure it cant slip

Dave

[electrofix]

Re: Smeg Int’ DW (DI 612 CA) no heat

anything like this ?

http://www.ukwhitegoods.co.uk/help/faul … ing-lights

Dave

[electrofix]

Re: Questions from a 4th year Apprentice

an insulation tester test at a voltage of 250 or 500 volts still known in the trade as a megger. A bit like biro and thermos flask who brought them out first

but you should also be familiar with a pat tester

as far as theory is concerned learn DC theory first than move onto AC later as its more complex than you think. get a grip of Ohms law its fundamental to understanding how electricity works

what you could do with is an electricans course just for the theory.

Dave

[electrofix]

Re: Whirlpool ADG7460 851144015871

cant see a picture of the motor but as lot of later motors are just sized up drain pumps

so

run the unit with the side off so you can access the motor. since the field coil of the motor is an electro magnet to see if its active touch the field laminations with a large screwdriver. if its active and not moving its gone

Dave

[electrofix]

Re: Siemens IQ300 WM14Q390GB

just thinking outside the box

wondering if unit starts to move motor and fails if it does not get impulses. may give you a different fault but cant be sure

have no access to Siemens error codes so have learned to try everything and check everything
one person on here seems to have Bosch tech access and maybe Siemens is Nomad

Dave

[electrofix]

Re: Siemens IQ300 WM14Q390GB

did you check for tacho output ?

Dave

[Author]

Posts