Forum Replies Created
-
Posts
-
Re: White Knight tumble dryer integrated – 831WV – clunking
dont think it will be the bearing but i can be wrong
have you looked at the rivets at the back of the drum which is a common problem. look at the drum see if it looks like its catching( look for scrape marks )
watch it go round and see if its in the same place evary time. if its a bearing it will vary if its the drum it wonthope it helps
DaveRe: Bosch Logixx 7 Flashing lights
some faults on bosch machines lock the unit so no more damage can occur
don’t know what the light mean as getting bosch fault codes is difficult but most common fault on machine is the carbon brushes in the motor. on the integrated units it is possible to change these through the cover at the bottom
as for the lock out try this ( not sure it will work on this unit ) but don’t rush it wait about a second between each step
plug machine in
turn timer knob to 6 o’clock position
press and hold spin speed button
turn timer knob 1 click clockwise
release spin speed button
now turn programmer knob to off wait 5 secs and turn onhopefully it will work but you may have to repeat a few times and some engineers say it only works with motor unplugged but I have not found that.
if anyone else knows if this is not correct reset for this unit please post
Re: Hotpoint CTD 80 Drum Not Spinning
sound very likely but the only way you can be sure is swop it. if it works ok if it does not them its probably the motor
Dave
Re: Miele T8926WP Fan Motor
I know what connect are like for upping the prices. it is going to be dear but I would ring miele themselves and see what they want
Dave
Re: Whirlpool DWF407 dishwasher, stuck in cycle 2beeps+1beep
i can see why you think its a heat problem but i would expect it to run longer before it stops. it barely has time to fill never mind detect if it heating.
you need to look at the event sequence what task does it complete. first it will pump out (does it stop) then it fills and stops when full or starts main motor as its filling (does it ? )Dave
Re: Puzzling Problem with AWOD 6727 Pump…any ideas?
machine will report clean pump if it thinks it still has water in it
inside machine you will find thin tub going to a switch at the top of the machine but it has a chamber at the bottom that traps air. if this chamber is clogged it will assume it is still full
beware dont blow into the top switch. some of the later switches are damaged by this and i cant be sure which type of switch it is in this model
Dave
Re: Bosch Exxcel SGS46E02 water problem
on this unit there is a little component called an “impellor jug” bosch part no 424099
this unit count the water into the dishwasher and if it fails unit starts but if the count is not there the unit aborts the prog to stop flooding
its a common fault
Dave
Re: White Knight C77AW condensation problem
not had problem but photo 1
looks like water leaking from condensor and poss steamDave
Re: bosch dw sms40a08gb/03
have you looked at the board and checked for damage. you do not want to fit a new board only to find you have a short that destroys the new one
Dave
Re: Hoover Time H160E not spinning after draining
fault 3 is pump time out ie it still thinks it is full of water after 3 mins
this could be
1 soap blockages in pressure chamber
2 stuck pressure switch
3 bad connections to timer pcb from pressure switchobviously the pcb is also suspect but you have to eliminate everything elase before thaT
Dave
Re: CDA WASHING MACHINE C1370IN
cant find a lot of info but my logic is as follows
CDA use Fagor washers, so fagor fault codes should be the same.
from the Fagor list F06 is “no heat within 15 mins” so if your symptoms seem to match this check it out
Dave
Re: Bosch WFX3267GB/10 – motor won’t turn
first check motor
check continuity on armature, field and tacho
if all ok check timer for blown tracks
Dave
Re: 680uf capacitors
i use rs components part no 526-1250
http://uk.rs-online.com/web/p/aluminium … 3132353026
Dave
