Forum Replies Created
-
Posts
-
Re: TKL9909 Washer Dryer drum bearings
sound like you may be right
if you take belt off machine and spin drum it should be silent if not then bearings going
from what i can see you can get the bearing but to confirm take the top off and look at the drum. if it has clips or screw going around the drum then it should split and therfore can be repaired
parts wont be that dear but it could be a long job as dont think the case front comes off so whole drum has to be taken out through the top. that means all the part on it and around it have to be taken off first
maybe someone else can confirm this
Dave
Re: CDA d/w CW447
cant see a cw447 but connect list a cw448 which seems to be a disguised smeg
what is wrong with board?
how does fault present itself ?Dave
Re: Siemens SE25M851GB Drain Pump
agree with martin but
if you feel you would like to donate to a charity of your choice as a thanks for the help you have recieved please do so
glad you fixed it
Dave
Re: Beko CDA539FW Door Hinge help
you beat me to it don
but if you look at diag no 8 on lower picture shows removing pin and put it back in the other side of the hinge to reverse it
Dave
Re: Beko CDA539FW Door Hinge help
most fridges have 1 set of hinges. when you reverse doors you just swop sides
DaveRe: CDA Dishwasher stops and flashes fault code
in any fault condition it goes back to first light ignor it its normal
in this case you have fault 1 ntc failureone flash pause one flash pause etc so you cant see a sequence
replace ntc if it goes ok if not its the boardDave
Re: Siemens SE25M851GB Drain Pump
you have not posted complete model but from what i can see try the following I have looked up model SE25M851GB/79
remove the lefthand side of the dishwasher
looking at the side you will see a chamber and just to the right you will see a red rod going vertically from a polstyrene float to a switch. if you lift that rod with machine switched on the pump will run.
be aware there may be exposed live connection on some of the switches so be carefulif pump now runs its not the pump.
if you go here
http://www.siemens-home.co.uk/store/spareparts/search
put in you complete Enrlook at diagram on page 4 chamber is item 0410 switch is item 0421
the rod is item 0526 on page 5Dave
Re: Siemens SE25M851GB Drain Pump
first question is why although these pump can fail i have not had to change one its normally glass or similar obstruction that can be removed from inside unit under filter
Dave
Re: Elba Excellence PX906 Faulty
i assume you mean grill with fan
i would take a look at the function switch.
these are prone to fail on most cookers contacts carry the heater currents and burn outremove switch ( you should not have to disconnect it) and turn it around so you can see the contacts moving and look for one that is not moving properly or burnt out
Dave
Dave
Re: Neff u1524
this is a train of bad new by the sound of it
from what you say you have replaced everything except the board. if the new ptc was now faulty it would not reach required temp before failing so it comes down to the board not turning element back on when it cools.
my only thought is the relay on the board that controls element. Did old element go bang and damage it ?Dave
Re: Hotpoint WMUD962
F12 seems to be a communication error between the 2 boards
check the connections both endsIf that fails
would have a word with EMW see if they will test both panels as a pair (and repair if necessary) if you post it to them
Dave
Re: Elba Excellence PX906 Faulty
but how hot does it get?
it is not possible to guess how hot an oven is beyond about 75 degrees after that it feels hot. you cook things at 200 degrees and that feels very hot. buy a thermometer to check.
check to see if oven has cooling fan. if yes is it working
you say only one mode seems to work but you dont say which
Dave
