[electrofix]

Re: whirlpool ADP5406

check the light above the start button. count number of flashes to get fault code

yes can be flow meter reed switches fail can be got from maplin and replaced

Dave

[electrofix]

Re: unpaid

i agree it all down to cost. The higher the amount the more reason to persue, but for £40 with no parts outlay his time is better served dealing with paying customers

Dave

[electrofix]

Re: unpaid

I do realise where most of you are coming from but in the end it is best use of time and its no worth it going through court
put it down to experience but make sure you mark his card and spread the word
there will come a day when he needs you, or one of his family. It might take a while but the day will come
At the end of the day you have lost a bit of fuel and time so on paper its about £10 give up and move on.

regards

Dave

[electrofix]

Re: Bosch Washing Machine ALL lights flash!

correct Bryan the only reason you register is to send you an offer to extend warranty

Dave

[electrofix]

Re: indesit carbon brush

was not 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} percent on model at first. i had it down as WA101UK but could not find that number

have now got model WIA101uk from commercial code

Dave

[electrofix]

Re: Samsung people?

have done one of these had a hell of a job sorting out
new board new wiring harness and the like. got info if you send me email address
Be aware got two faulty boards from connect both boards had blown r111 due to idiots fitting without wiring mod check this resistor before fitting
have still got old working board got fault wrong was tripped overheat stat not board if you get stuck

my original post

post327708.html#p327708

regards

Dave

[electrofix]

Re: Bosch Washing Machine ALL lights flash!

try a software reset

from memory i think its

set prog knob to 6 o clock ie pointing down
press and hold spin speed button
turn timer knob 1 click clockwise
let go
turn off and then try machine

if I am wrong I am sure nomad or someone will correct me

Dave

[electrofix]

Re: indesit carbon brush

johnnyj wrote:C00114885 cost more than the machine is worth. JJ

qualtex show this part number cross ref ro car99 which means the carbon face is still the wrong way

looks like its a cut reverse and resolder job

Dave

[electrofix]

Re: Help my Candy GrandO washing machine Door security Led k

anything that goes flash is normally big problems

my guess is the door lock has failed and taken out the programmer but i hope to be wrong

at under 2 years old this machine could be described as unmerchantable quality and not fit for the purpose as a reasonable person would expect an appliance of this type to last longer than this
look up guarentees on google in particular sales of goods act
then approach the retailer as your contract is with them. do not let them fob you off to the manufacturer as the retailer has ultimate responsibility

hope this helps

Dave

[electrofix]

Re: indesit carbon brush

that what i will do if i have to but i assumed there must be a correct part and if I get a customer asking for them its nice to know the answer

thanks

Dave

[electrofix]

Re: AEG Competence Oven stops working

in your case the whole oven is controlled by a computer so does not use the same relay
not seen many of these but it seems like a similar problem. you need to check if the cooling fan is running. it may be jammed or not turning fast enough

Dave

[electrofix]

Re: Old hoover junior

your bringing back memories now

the days when you could buy every part of the motor had one old dear used to take one of these apart to dust it on a regular basis and lost the armature

complete with (almost) dust proof bag

Dave

[electrofix]

Re: Bosch WAE24363GB/05 FD 8806601337 Dead Blank/No Displa

leavemetogetonwithit wrote:Wonder if that’s what’s referred to as a “fusible resistor”?
http://docs-europe.electrocomponents.com/webdocs/0027/0900766b8002759f.pdf

Mike.

very likely m8

Dave

[electrofix]

Re: Bosch WAE24363GB/05 FD 8806601337 Dead Blank/No Displa

had a bosch a while ago dead panel

there is a 10 ohm resistor in series with board supply and it goes open circuit. should have coloured bands on it brown black black

Dave

[electrofix]

Re: Bosch Motor

endframe was used as brush repair on this early motor
on later motors you can get at the end of the brushholders and remove brushes
if your motor has visible brush holders this end unit wont fit

? why do you need an endframe ? brushes now available car70

Dave

[Author]

Posts