[electrofix]

Re: bosch logix 8

sound like brushes then thanks

did not want to drive 30 miles to find out i could have taken spares with me

can we have a bosch fault code list in the known codes section please

Dave

[electrofix]

Re: whirlpool awd5404

no easy to tell from this all this means is the pcb has detected a fault could be all sorts

would check motor and heater first and take it from there

hope this helps

Dave

[electrofix]

Re: beko wma1614w washing machine

from what i am reading seems to be related to pump triac on pcb

send me your email will send you fault flow chart

Dave

[electrofix]

Re: WMA 745W Beko

cant promise it will help but give me your email and i will sent you some pdf’s

Dave

[electrofix]

Re: CW194

take it you check obvious l ike broken wires in the door

if you get continuity back to pcb would suspect the board look for cracks and obvious component failures

Dave

[electrofix]

Re: Samsung and askoll pumps .

never had a prob but will always either reuse coils or fit askoll with built in temp overload

Dave

[electrofix]

Re: Zanussi FX1265. bleeping

reading of alarm codes

The last alarm code can be displayed even if the programme selector is not in the tenth position
(diagnostics) or if the appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and any of the option buttons for at least two seconds: the
LEDs initially switch off, and then display the flashing sequence corresponding to the alarm.
The alarm sequence continues as long as the two buttons are held down.

try this

if you want full manual

let me have you email and product code

Dave

[electrofix]

Re: hotpoint wd860 washer dryer

wow how lucky are they no to have had a serious fire

wht happened to thermal cut outs stopping this

Dave

[electrofix]

Re: CDA CW492 dishwasher

if its a whirlpool had one yesterday same fault

open programmer and replace 1.5 uf cap on board large grey block

its the power supply to the board cured mine no probs

hope this helps

Dave

[electrofix]

Re: SK88800I

the large grey block by the left hand plug is the power supply cap

looks to be a 1uF but it will be printed on it

replacement must be correct value and capable of taking over 250 v ac

if it does not work you habe not lost much as they are quite cheap

i source mine from http://www.rswww.co.uk
example

part number 441-9688 is a 1uF cap 300 vac with a lead spacing of 22.5 mm cost 63p each sold in packs of 10 but no p&p next day delivery

but you will have to look at the values on your component

hope this helps

Dave

[electrofix]

Re: SK88800I

also the components may not look damaged so you may not see anything its just getting tired

Dave

[electrofix]

Re: SK88800I

you are not looking for a power supply toi the door but to the whole pcb

find live input to board and follow tracks on board to see what components it goes through first

you could send me a photo of board if you like and i will hazzard a guess

[electrofix]

Re: SK88800I

long shot here

sound like a power supply fault on th pcb

ie board is ok until you open door : door light relay energises : power drops on pcb : and display goes out

fault is similar to a low battery small amounts of power ok larger amounts and it fails

look for power source on pcb a lot of the times it is a capacitor around 1uf or so and these go down with age

get similar faults on ariston dishwashers

hope this helps

Dave

[electrofix]

Re: Zanussi ZDE57140w Tumble Dryer

hi steve have got manual for

916093857 00

if it helps let me have your email

Dave

[electrofix]

Re: zanussi td4112 timer

number was 125 11 06 00 /9

which became 125 11 06-02/5

number becomes 125 11 06-03 / 3

hope this helps

Dave

[Author]

Posts