[electrofix]

Re: tds online

thanks but i already use Qualtex its the lux tds access address i need

Dave

[electrofix]

Re: maytag fridge fault

a lot of machines these days do a check of componebts before start up so it is possible

can you either
A place the defost heater so it is not earthed
B disconnect earth of the whole appliance

this is for check purposes only i am in no way telling you leave the earth off the machine so it will work

i do the same on indesit washers when the earth fault in the motor causes problems

hope this helps

Dave

[electrofix]

Re: wf541

look in here

http://www.ukwhitegoods.co.uk/modules.p … c&start=30

Dave

[electrofix]

Re: zanussi wzd 12270w not starting

let me have your email address will send you some light reading

Dave

[electrofix]

Re: tds online

i buy direct from lux quite often no need for account pay with card 25 discount no probs

tel 01325 302464

when it askes for your trade account number press hash to jump and tell them you want to pay by c card no

what i need is the web address of the lux access online have been given a poss account nuber and pass but dont know the right web address so am looking for someone who subscibes to tds online

tried tradeplace but have not got accounts with any manufacturer so cant use it

thanks

Dave

[electrofix]

Re: tds online

dont know but i dont spend enough to have an account

any other ideas

Dave

[electrofix]

Re: BEKO WM8127W Door seal

try 2905570300

from beko site

Dave

[electrofix]

Re: Zanussi WJD1667W drier issues.

looking at the tech info on the drying cycle it reads

1 calibration time out 10 min pump on
2 tap test water level 10mm time out 10 min pump off
3 cool down time out 20 min
4 dry time ou 20 min

i assume you stop working between 1 and 2

have you tried pouring a small amount of water in soap draw it looks to me as if it is waiting for a water level although explanation in the tech manual is not good. check for blockages in pressure circuit that may stop dryer but may not stop wash with more water taken in

bit of guess work on my part but worth a try

hope it helps

Dave

[electrofix]

Re: zanussi zj1217

turn prog to reset

turn off machine if already on

press and hold start and pause button with 1 hand

turn on machine

hold buttons till machine buzzes or light flash

you are now in diagnostic mode

turn prog knob 6 clicks clockwise should now show fault code

pm me your email will send you the manual
but let me know the prod code there are 2 variations of this unit

Dave

[electrofix]

Re: Zanussi WJD1667W drier issues.

have you checked cold water valve a lot of these machines wont start the dryer till it detects the cold water

hope this helps

Dave

[electrofix]

Re: ge monogram

as an educated guess i would say a power supply fault on the pcb

just like a low battery if you pull too much power it cuts out

a lot of units use a capacitor for this and the go down with age

i dont repair fridges but if you want email me a good picture of the pcb and i will try to hazzard a guess of what to change

hope this helps

Dave

[electrofix]

Re: bosch logix 8

found problem searched forums and found reset proceedure

reset machine now working ok

another job i would not have cured without the help of this forum

thanks to all

Dave

[electrofix]

Re: bosch logix 8

changes brushes still shows F43

do you have to do a reset proceedure after fault

thanks

Dave

[electrofix]

Re: viking bw11 commercial washing machine

rang the only contact i have for viking
some parts are still available but they have not got a hinge

hope this helps

Dave

for ref i rang anglo west on 0844 3910395

[electrofix]

Re: hotpoint wf860

i would talk to EMW
they programme the boards so if you other board only needs a software change they will do it thay can also test you existing board

Dave

[Author]

Posts