[electrofix]

Re: Whirlpool just pumps?

these would be my next moves

check for earth faults on pump if neutral switched

check voltage at pump if 110v triac failure had a servis do this recently

check triac in programmer

hope this helps

Dave

[electrofix]

Re: aeg d/w 911232040 no fill

got wiring diags and timer charts any use??

Dave

[electrofix]

Re: SMEG SUK62MFX5 cooker with gas stove.

silly idea ? you did disconnect element to read resistance

i prefer to test live no room for error

if element ok you need to know if live or neutral missing could be a chaffed wire that has blown to earth and now is o/c

hope this helps

Dave

[electrofix]

Re: Whirlpool AWO/D 4605

if it was me my next move would be to check for L+N on the door lock or power door lock up seperatly to check operation you can find right terms with multimeter if it is a heater type

also find the live and switch wire to the machine and short out to see if it bursts into life

hope this helps

Dave

[electrofix]

Re: Whirlpool AWO/D 4605

if it is the same as awod 4505 have got one i can send you out of scrapper also complete front panel not sure if it is the same

Dave

[electrofix]

Re: Miele Tumble dryer

yes that is strange i would check harness for chaffed wires may be shorting with vibration

cant understand why not blowing fuse and still welding relay

Dave

[electrofix]

Re: AEG 50630

assume customer has not got rinse hold set ?

Dave

[electrofix]

Re: aeg 74630-10

Thanks

Dave

[electrofix]

Re: aeg 74630-10

checked tacho magnet was loose but still turns and gives output

Dave

[electrofix]

Re: Miele Tumble dryer

you have not said how this contactor has failed

if the heater had shorted i would expect it to blow the fuse and maybe weld the contactor contacts together

if as you describe this is a burn out unless moisture is getting inside vthe contactor than this can only bad electrical connections. cut the wires back far enough to find clean wire and replace with new good quality connectors that are tight any loose conns will get hot and burn out

hope this helps

Dave

[electrofix]

Re: Hotpoint Condeser Dryer CTD40

heater thermostats tripped common fault check condensor unit is very clean

regards

Dave

[electrofix]

Re: hpt WM62 hangs

agree sound like cold inlet valve failed it will fill on wash ok through hot but stick on first and second rise will do last rinse through softner valve

Dave

[electrofix]

Re: Whirlpool H Duty T/Dryer

i assume you put the right type of fuse in

must be T 6.3a not F 6.3a

have seen other posts about these dryers the top loader autos use the same fuse but in the dryers case i think if you overload it the motor will blow the fuse as it changes direction on start up

Dave

[electrofix]

Re: Whirlpool H Duty T/Dryer

long shot

check the agitator these machines the top half of the agitator moves in one directon but is locked in the other by small pawls that wear and allow agitator not to wash properly

test hold top of agitator turn by hand clockwise and anticlockwise should lock in 1 direction cant remember which

Dave

[electrofix]

Re: Whirlpool sensor rear vent dryers awz 3518 no heat

have no knowledge of this machine but an ntc is only a temperature contolled resistor if you substitute various fixed resistors you should get the heators to turn on and off try

http://www2.westfalia.net/shops/electro … e5fc0c7083

this is a decade resistance box so you can switch in various values quickly

it would be nice if you knew the resistance of the ntc at a given temp to help diagnosis but you can measure the in situe while you are switching in and out resistors to turn on and off heater

hope this helps

Dave

[Author]

Posts