Forum Replies Created
-
AuthorPosts
-
electrofix
Moderatorhttps://whirlpoolservice.co.uk/washi…ir/error-codes
well according to this it could be the dryer sensor
worth checking
Dave
June 28, 2023 at 6:25 pm in reply to: Zanussi ZWG7160P Spin Not Very Good Lately after Replacing Bushes & EWM Module #487293electrofix
Moderatorwith brushes the model and pnc are just a good guide
the motor info is also required as they fit more than one motor in a production runthere are more then one seller of zanussi spares inc the manufacturers own site
Dave
electrofix
Moderatorhave some fun
take a cricket batDave
June 25, 2023 at 4:02 pm in reply to: Zanussi ZFT10210WA freezer constant red light and beeping sound #487350electrofix
ModeratorJune 25, 2023 at 2:43 pm in reply to: Zanussi ZFT10210WA freezer constant red light and beeping sound #487348electrofix
Moderatorfridge freezer thermometer
Dave
June 25, 2023 at 2:40 pm in reply to: Zanussi ZFT10210WA freezer constant red light and beeping sound #487346electrofix
Moderatoryou say its set to -18 but have you measured the temp ?
Dave
June 24, 2023 at 8:18 pm in reply to: how old is my washing machine? and, advice for a potential replacement #487342electrofix
Moderatorwell serial no usually are
first digit year
second and third month
but there are not 16 months so check again
did find it on hotpoint spares
https://www.hotpoint.co.uk/spare-parts/bom/fml942kuk-769991567130
assume you have mis read commercial code
Dave
electrofix
Moderatorcomes up as a line sage relay fault. main board failure
take a close look at the board round the power relays. look for bad solder joint and hairline cracks in the board
Dave
electrofix
Moderatorok found it
sent you all i can find
Dave
electrofix
Moderatorshillo wrote:The stuff thats in there seams to be well frozen
it can be well frozen at -10 but its not safe
Dave
June 23, 2023 at 7:19 pm in reply to: Zanussi ZWG7160P Spin Not Very Good Lately after Replacing Bushes & EWM Module #487289electrofix
Moderator1. The waste water pipe pulsates as if water going through it (even though the drum is empty, including the filter area at the bottom of the drum)
thats normal nothing to worry
2. It spins normally with nothing at all in it
which means it can
3. As it’s getting to the higher rpms, I am noticing it sparking (more reflected light from the side panels as I can’t see the brushes directly)well that could be it. depends why they are sparking. they will spark more with higher loads. try taking out the brushes, look at the face, the shiny bit is where the contact is. if it only in contact a small amount try rub obb just the shiny bit with emery. be carful its soft and you only want a little but off. then see if it sits better and does not spark as much
if the motor clicks as it turns around and you have a high segment in the armature then you need a new motor
4. The pipe from the pressure switch has no objections whatsoever, with no effort at all to blow throughgood
Dave
electrofix
Moderatorsound like your wife is right
you need to get a better thermometer. if food is not kept at -18 or below it wont keep as long. it could be -5 which would be dangerous for long term storage
How Long Does Food Last In The Freezer? A Food Safety Guide (highspeedtraining.co.uk)
Dave
electrofix
Moderatorso all the low voltage side did not work ?
if yes change chip and see what happens
Dave
electrofix
Moderatorok the freezer maybe ok temp but have you measured it ?
does the compressor switch off or iis it running all the time ?
these systems cool the freezer first and only when that gets down to temp is there enough gas left over to cool the fridge. if the freezer is not cold enough the fridge will never cool. if the compressor never stops apart from the energy cost it will mean a tired compressor or low gas levels
Dave
June 23, 2023 at 7:36 am in reply to: Kenwood KS100G Thermocouple replaced but still pilot light goes out #487328electrofix
Moderatorfrom the sound of it you have replaced all the components but from our position this is a gas appliance and all we can do it suggest you call a gas safe engineer
Dave
-
AuthorPosts
