garn

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 433 total)
1 2 3 4 5 6 … 27 28 29
  • Author
    Posts
  • November 16, 2015 at 10:29 pm in reply to: Bosch WAQ washing machine door repair?? #432804
    garn
    Participant

    Re: Bosch WAQ washing machine door repair??

    thanks for the reply.
    Are-these the Jap models WAQ?.
    Drum shafts are always going on these to.

    thanks garn

    June 5, 2015 at 9:31 pm in reply to: Toolbags #427912
    garn
    Participant

    Re: Toolbags

    Have a look at This best one iv Had so Far tool bags don’t last very long iam quit impressed with C.K MAGMA (http://www.electricians-direct.co.uk/bu … s_1676.htm )

    June 5, 2015 at 12:28 pm in reply to: Candy CDB7540/1-80 Intergrated washer dryer #427857
    garn
    Participant

    Re: Candy CDB7540/1-80 Intergrated washer dryer

    THANKS MATE SORRY IM LATE GETTING BACK TO YOU .YES THE TIE STRAP THE SWITCH IS A GOOD IDEA .
    MEANWHILE IV MANAGED TO GET A DIAGRAM FROM HOOVER THEMSELVES.
    THERE STILL BASED IN Merthyr Tydfil 😮 , .

    IV TRIED TO LOAD THE DIAGRAM IN THIS THREAD FOR ANY ONES REFERENCE BUT FAILED CAN 1 OF THE MODERATORS OR KEN SEND ME A LINK SO THEY CAN LOAD THIS DIAGRAM

    THANKS PAUL…

    April 21, 2015 at 4:20 pm in reply to: Hot-point WDL 540 updated Lock replacement #426665
    garn
    Participant

    Re: Hot-point WDL 540 updated Lock replacement

    Thanks Jim its a fix motor coms.
    Paul

    Sent from my GT-I9505 using Tapatalk

    April 21, 2015 at 10:23 am in reply to: Hot-point WDL 540 updated Lock replacement #426664
    garn
    Participant

    Re: Hot-point WDL 540 updated Lock replacement

    thanks for being so prompt Jim .no on this occasion i though the job was a quick fix. so was there on Sunday.

    ill call back this afternoon and go through it thoroughly.

    and thanks for the prompt answer so i can be off to work now

    Thanks Paul

    February 4, 2015 at 7:25 pm in reply to: HTP x2 WMUD 962 942 Pressure switch reset #424342
    garn
    Participant

    Re: HTP x2 WMUD 962 942 Pressure switch reset

    Ok thanks.

    Sent from my GT-I9505 using Tapatalk

    February 3, 2015 at 10:55 pm in reply to: HTP x2 WMUD 962 942 Pressure switch reset #424340
    garn
    Participant

    Re: HTP x2 WMUD 962 942 Pressure switch reset

    Just wondering hotdog said i would need hotpoint top prog the board.
    I have the card reader and lower end adapter is this when this kit comes it ?
    If i purchased thae card to program in it may cure it.
    Paul

    Sent from my GT-I9505 using Tapatalk

    February 3, 2015 at 9:47 pm in reply to: HTP x2 WMUD 962 942 Pressure switch reset #424339
    garn
    Participant

    Re: HTP x2 WMUD 962 942 Pressure switch reset

    Thanks very much for the advice .B E R it them. Iv been all ready competing with argos to repair it .
    Thanks Paul

    Sent from my GT-I9505 using Tapatalk

    January 21, 2015 at 10:00 am in reply to: AEG Condenser Dryers #423835
    garn
    Participant

    Re: AEG Condenser Dryers

    Thanks for the info.
    Are these codes just for the E lux group .or are they all the manufacturers factory codes.
    Thanks garn

    Sent from my GT-I9505 using Tapatalk

    January 7, 2015 at 1:26 pm in reply to: Samsung RL33SBSW1/exu fridge freezer #423333
    garn
    Participant

    Re: Samsung RL33SBSW1/exu fridge freezer

    Ok thanks il have a look later
    paul

    December 12, 2014 at 10:46 am in reply to: bosch wae24466/gb03 error 21? #422578
    garn
    Participant

    Re: bosch wae24466/gb03 error 21?

    Ok thanks for the info il try it this afternoon.

    December 11, 2014 at 9:43 pm in reply to: bosch wae24466/gb03 error 21? #422576
    garn
    Participant

    Re: bosch wae24466/gb03 error 21?

    Thanks for the reply when i left yesterday the error went from F21 to F63

    Still Bewildered Garn..

    December 9, 2014 at 11:05 pm in reply to: No more ASKO? #422504
    garn
    Participant

    Re: No more ASKO?

    Try Changing The Door Seal sounds like the inner drum rubbing against the seal.
    Which it does normally. they do now and again squeak .just before the end of spin. or during rotation. 😉

    Garn…

    December 9, 2014 at 11:30 am in reply to: Hoover 380-80 Vent Dryer #422490
    garn
    Participant

    Re: Hoover 380-80 Vent Dryer

    garn wrote:Thanks martin its the same heater that’s coming up with the part number you gave.
    same 1 in connect that i had yesterday. it has a block on it instead of 4 wires.
    im sorry still confused

    Just been on to hoover direct its down to there info

    Just to Clarify the heater with 4 separate wires is (40004314)

    December 9, 2014 at 10:49 am in reply to: Hoover 380-80 Vent Dryer #422489
    garn
    Participant

    Re: Hoover 380-80 Vent Dryer

    Thanks martin its the same heater that’s coming up with the part number you gave.
    same 1 in connect that i had yesterday. it has a block on it instead of 4 wires.
    im sorry still confused

  • Author
    Posts
Viewing 15 posts - 61 through 75 (of 433 total)
1 2 3 4 5 6 … 27 28 29