jackster

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 172 total)
1 2 3 … 7 8 9 10 11 12
  • Author
    Posts
  • September 19, 2009 at 4:41 pm in reply to: Whirlpool TOP LOADER AWE6517 #297464
    jackster
    Participant

    Re: Whirlpool TOP LOADER AWE6517

    Wash & Rinse light on together indicates fault code F12′ which is ‘Heating element, short circuit’ Hope this helps mate, if you PM me with you E Mail adress I can send you more info, Cheers Chay

    September 18, 2009 at 5:34 pm in reply to: Candy CDC266 Dryer #297415
    jackster
    Participant

    Re: Candy CDC266 Dryer

    Cheers Chris!

    September 15, 2009 at 4:54 pm in reply to: Servis M9503W W/D #297126
    jackster
    Participant

    Re: Servis M9503W W/D

    Ok thanks for that, PCB is expensive so Ill give it a swerve!

    September 15, 2009 at 4:51 pm in reply to: Diplomat ADP8332 #297139
    jackster
    Participant

    Re: Diplomat ADP8332

    F4 is Drain failure & F2 is water in drip tray, sounds like it has overfilled.

    September 15, 2009 at 4:23 pm in reply to: Hoover SE264-80 – Module #297030
    jackster
    Participant

    Re: Hoover SE264-80 – Module

    I checked the hot valve, thats ok. I will check the timer for stains though.. thanks martin.

    September 15, 2009 at 4:04 pm in reply to: Hoover SE264-80 – Module #297028
    jackster
    Participant

    Re: Hoover SE264-80 – Module

    Thanks for the advice, after a bit of TLC on the pcb & connections I have got it running, however it is not playing ball completeley! It now stops after around 10 mins on each cycle except the boil wash were it is dead, doent want to know. I have checked the element isnt down to Earth, checked stat – A/OK. Door lock I replaced anyway, still the same??

    September 11, 2009 at 9:39 pm in reply to: awz 650 steam from door #296838
    jackster
    Participant

    Re: awz 650 steam from door

    The doghnut seal at fron is a common failure,
    the part number is: 481246688863

    September 11, 2009 at 9:36 pm in reply to: Hotpoint WMA34P #296748
    jackster
    Participant

    Re: Hotpoint WMA34P

    jackster wrote:Got it sorted! It was the PCB, luckily I had one a scrapper of the same model and it worked a treat. Cheers all.

    Or so I thought! It is working fine until the final spin then stops, If I select spin manually it spins great? Any Ideas?

    September 10, 2009 at 6:03 pm in reply to: Hotpoint WMA34P #296747
    jackster
    Participant

    Re: Hotpoint WMA34P

    Got it sorted! It was the PCB, luckily I had one a scrapper of the same model and it worked a treat. Cheers all.

    September 7, 2009 at 5:07 pm in reply to: Candy CDC266 Dryer #296504
    jackster
    Participant

    Re: Candy CDC266 Dryer

    Cheers Martin, all ordered. 😉

    September 6, 2009 at 4:11 pm in reply to: White Knight User manuals #296359
    jackster
    Participant

    Re: White Knight User manuals

    Yeah, thought as much,
    Cheers Don

    September 4, 2009 at 7:28 pm in reply to: ADP4400 Whi… #296310
    jackster
    Participant

    Re: ADP4400 Whi…

    You get some really weird faults when an NTC goes down, I have had this before, replaced the NTC a/ok

    September 3, 2009 at 4:10 pm in reply to: Hotpoint WM52P #296193
    jackster
    Participant

    Re: Hotpoint WM52P

    Replaced motor plug with new connectors and sorted, thanks for all your help.

    September 1, 2009 at 7:34 pm in reply to: Whirlpool AWM8123 door locks and that it is. #296023
    jackster
    Participant

    Re: Whirlpool AWM8123 door locks and that it is.

    This fault is normally motor related, if you have checked the brushes I would check motor itself and wiring

    September 1, 2009 at 11:02 am in reply to: Servis M6602W #295962
    jackster
    Participant

    Re: Servis M6602W

    Nice one, got it. Not to bad price wise really are they.

  • Author
    Posts
Viewing 15 posts - 106 through 120 (of 172 total)
1 2 3 … 7 8 9 10 11 12