johnmac11

Forum Replies Created

Viewing 15 posts - 616 through 630 (of 1,760 total)
  • Author
    Posts
  • in reply to: ananlogue meggar wanted #340388
    johnmac11
    Participant

    Re: ananlogue meggar wanted

    what about this one HERE, it is bloody cheap too…..


    John

    in reply to: Whirlpool AWM850 Stopping #340380
    johnmac11
    Participant

    Re: Whirlpool AWM850 Stopping

    It might well be a rinse hold, this machine will automatically rinse hold on easy care, delicates and the woollens program.

    John

    in reply to: Hotpoint Quadrio model CM04FFE /FF4D KUK #340288
    johnmac11
    Participant

    Re: Hotpoint Quadrio model CM04FFE

    Hi Helo_75,

    I saw the bulletin and the one I have is does not need the hinge cover, the bulletin says that the cover should be fitted on products before serial number 906020001. The one I have is well after that and according to the bulletin I have the new cover( which appears to still cause the problem ).

    The pcb is at the top and I checked this afternoon with the customer and the fridge freezer is working fine now that the wires to the door are disconnected.

    Thanks

    John

    in reply to: Hotpoint Quadrio model CM04FFE /FF4D KUK #340286
    johnmac11
    Participant

    Re: Hotpoint Quadrio model CM04FFE

    Thanks Jim, its appreciated. 😀


    John

    in reply to: Hotpoint Quadrio model CM04FFE /FF4D KUK #340284
    johnmac11
    Participant

    Re: Hotpoint Quadrio model CM04FFE

    iadom wrote:There is also a note that says the door magnets must be swapped over from the old door.Jim.

    Magnets?? are there 2. I assume they are hiding behind the trim at the top or bottom of the door.


    John

    in reply to: Hotpoint Quadrio model CM04FFE /FF4D KUK #340282
    johnmac11
    Participant

    Re: Hotpoint Quadrio model CM04FFE

    I suspected it would be a door as soon as I looked at it. :snig:

    I assume the code is 81541630300 and and the full model number is FF4DXUK, do you have a part number for this please Jim?

    thanks

    John

    in reply to: Hotpoint Quadrio model CM04FFE /FF4D KUK #340280
    johnmac11
    Participant

    Re: Hotpoint Quadrio model CM04FFE

    You’re correct Jim, Being a careful sod I took a picture of the rating plate and I have just noticed that the number i posted is the “type” number. Model number is FF4D(UK)

    I also meant to say earlier that the harness going through the door is just a piece of 5a black 3 core, I can imagine these being an earner from now on 😆

    John

    in reply to: whirlpool oven element #340067
    johnmac11
    Participant

    Re: whirlpool oven element

    Wrong model number I assume it is a G2P62F/SS/01
    If so there are 3 different versions but the circa element is the same for all of them 481225998405

    John

    in reply to: F&P fridge – rubber mount for evaporator fan gone #339637
    johnmac11
    Participant

    Re: F&P fridge – rubber mount for evaporator fan gone

    There are a few different versions of the 521T over the years. Can you post up the PN or Product number which you will find on the rating plate and I can then let you know if the mount is available. The PN number is usualy 5 digits long and sometimes has a letter at the end of it.


    John

    in reply to: Maytag GC2228GEH3 parts manual #339274
    johnmac11
    Participant

    Re: Maytag GC2228GEH3 parts manual

    Cheers Andy 😀

    in reply to: Letters On DEGs #338586
    johnmac11
    Participant

    Re: Letters On DEGs

    Did you send the letter to ISE by special delivery 😆

    John

    in reply to: RANGEMASTER DATE CODES?? #338436
    johnmac11
    Participant

    Re: RANGEMASTER DATE CODES??

    Anyone know????

    John

    in reply to: best landline provider #338146
    johnmac11
    Participant

    Re: best landline provider

    If you have broadband in the shop take a look at http://www.vonage.co.uk I pay about £13-£15 all in each month and it has a few extras included like emails with your voicemails attached, call diversion etc..

    John

    in reply to: In search of the fourth cord #284503
    johnmac11
    Participant

    Re: In search of the fourth cord

    you are probably right but loking at the posts he has contributed to he must be in the trade. Problem is if joe public looks at his username they will assume he is trade and that all he says is gospel.

    John

    in reply to: In search of the fourth cord #284501
    johnmac11
    Participant

    Re: In search of the fourth cord

    What a pratt. I wonder if he has read Martins megger thread??

    John

Viewing 15 posts - 616 through 630 (of 1,760 total)