Forum Replies Created
-
AuthorPosts
-
johnmac11
ParticipantRe: Bauknecht gsx7551 manual
Those two neons are to tell you that the salt chamber and rinse aid dispenser are empty.
John
johnmac11
ParticipantRe: Another joke.
I’m sure that you have seen pharmaceutical advertising in doctor’s offices on everything from tissues to note pads.
Well, in my book, this one should get the prize….

I e-mailed it to my Chinese doctor friend…
He e-mailed back:
“If light stay on more than 4 hours, call erectrician.”johnmac11
ParticipantRe: Has this site been mentioned on here before ?
Hi Shaun,
Link now sorted.
Johnjohnmac11
ParticipantRe: Whirlpool NTC reading
Here are the correct values for Whirlpool dishwasher NTC’s
20º = 58.1 kΩ
25º = 47.1 kΩ
30º = 38.2 kΩ
40º = 25.4 kΩ
50º = 17.2 kΩ
60º = 11.8 kΩ
70º = 8.3 kΩ
80º = 6 kΩ
85º = 4 kΩJohn
johnmac11
ParticipantRe: whirlpool AVM965/1x microwave/ cooker hood combo…….
Just took a lok at the wiring diagram for this one and the quality of the diagram is worse than the microwave itself. It can only be one of the door switches or god forbid the ccu which going by my out of date price list is £184….
Cut your losses and run methinks.
John
johnmac11
ParticipantRe: whirlpool AVM965/1x microwave/ cooker hood combo…….
Was the microwave dead??
John
johnmac11
ParticipantRe: whirlpool AVM965/1x microwave/ cooker hood combo…….
Quality machine… did you have to take it off the wall :rotfl:
John
August 16, 2010 at 9:18 pm in reply to: WHP 3XLER5435HQ comm. super-big tumble dryer belt change. #328012johnmac11
ParticipantRe: WHP 3XLER5435HQ comm. super-big tumble dryer belt change
Easy job Mike.
The strange clips are actualy lid hinges, take out the the screws on the clips, take the filter out and you will see two screws there to remove. Then push the lid forward from the back and pull upwards on the front of the lid, it will hinge up from front to back, be careful here as the clips might fall out. Disconnect the door microswitch and then take out the two screws at the top of the front panel. Pull the front panel up and it will release the hooks that hold the bottom of the panel on and it should be obvious from there on in.John
johnmac11
ParticipantRe: New member proposed
Welcome to the war room Ade, lots of reading in here for you to catch up on..
Have fun.John
johnmac11
ParticipantRe: whirlpool door interlock
😳 480111101392
John
johnmac11
ParticipantRe: whirlpool door interlock
part number is 4801111013092
John
johnmac11
ParticipantRe: Where can you get one of these ??
They have never been available in the UK as a spare part, lots of Whirlpool engineers had them issued to them years ago but no more.
I find a pair of mole grips clamped onto the nut and a quick whack with a hammer gets them off easilyJohn
August 9, 2010 at 4:33 pm in reply to: Whirlpool AKZ446 FCSM6 2.3kw Single Oven Displaying ‘Stop’ #327250johnmac11
ParticipantRe: Whirlpool AKZ446 FCSM6 2.3kw Single Oven Displaying ‘Sto
You can find the switch HERE in the shop
HTH
John
August 9, 2010 at 4:09 pm in reply to: Whirlpool AKZ446 FCSM6 2.3kw Single Oven Displaying ‘Stop’ #327248johnmac11
ParticipantRe: Whirlpool AKZ446 FCSM6 2.3kw Single Oven Displaying ‘Sto
Hi Al,
We would never condone bypassing anything, the button is there for a reason and if bypassed and something went wrong your house insurers would not pay out.
If you can have a multimeter it is easy to check and see if the button is faulty. If it is faulty can you post the 12nc number from the oven ( on the barcode label starting 85***) and I will get the part number for you.
JohnAugust 9, 2010 at 3:26 pm in reply to: Whirlpool AKZ446 FCSM6 2.3kw Single Oven Displaying ‘Stop’ #327246johnmac11
ParticipantRe: Whirlpool AKZ446 FCSM6 2.3kw Single Oven Displaying ‘Sto
Has the main oven knob been switched to the off position before you press the middle button??
If not turn it to off then try again, if it is at off and still does not set then the most likely culprit will be the middle button.
John
-
AuthorPosts
