Forum Replies Created
-
Posts
-
Re: Hoover HSPF167 buzzing noise (over phone).
👿 Was exactly same damage to new board as had occurred on old one. Toc had gone again in motor but for no apparent reason. I BER’d it and gave her most of money back. There was a tiny little bit of burning sign around where the tacho wires junction from the loom into the motor plug. I have since thought that maybe the tacho wires were intermittently shorting at that point, causing the motor to go into spin during wash. Anyway, not worth chucking good money/time after bad. Next time anyone says “Nextra” I will use a long stick.
Mike.Re: AEG LAV61300 91400112901
Looks like front comes off after you remove control panel. PDF’s on mediator.
Mike.Re: zanussi zwf16581 no water intake.
The tech is all on Connect mediator. (l/h column on homepage, select appliance type and follow from there) But my bet would be that it won’t be a lot of help. I would try unplugging components in turn and see if anything changes. Have you checked that machine is fully emptied and p/sw reset? If you don’t have a Connect a/c pm me but I probably won’t be logged in till tomorrow evening.
Mike.Re: zanussi zfc 56/48
If you have an account with Connect you can find the parts you require through mediator. There are hundreds of models for Zanussi. Next time please specify what type of appliance it is. I spent a fruitless three minutes looking under cookers. (More fool me.)
Mike.Re: Baumatic Thermostat Alternative
Part number given by mediator is BMTX1170000599.
Masterpart have FIL1170000599 “in stock” at £23.35. Said to fit BT401SS
Mike.Re: Hoover HSPF167 buzzing noise (over phone).
Hmm. Went back and installed new toc on Friday. Tested all OK and working fine. Got my money and away.
A few minutes ago she rings up and tells me it only did two washes and then died. 🙁
Apparently it’s now dead, no lights, nothing. She has checked plug, fuse etc.
She says that when she turns it off it gives a little “plink” as though something is going on. 😕
Any ideas? Probably be going back Weds or Friday.
Mike.Re: hotpoint/indesit spares
Hotpoint
will give you 20{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} trade discount with no questions asked if you’re paying over the phone with a card. They’re sometimes cheaper than our wholesalers for less common parts. That said, I’m still waiting for a DC27 fascia panel I ordered before Christmas which was supposed to be “due in soon.”:evil:
Mike.Re: hotpoint wd440 aborting program
Should be worth trying a pressure switch or, if you don’t have one, open up the old one to check it, which you can do without personal injury if you’re careful. Occasionally they have a broken switch contact which flaps about instead of acting positively, leading to intermittent and strange faults. If not that, maybe it’s a fault somewhere in the wiring loom.
When you say, “heater seems to come on” that could be just the system self-check, if it doesn’t stay on, so it could be a red herring.
Mike.Re: They dont build em like that anymore – Part 20
Got home this evening to find a message on the answerphone.
Sounds like an older gentleman.“Hello. I’d just like to enquire whether you deal in second hand Creda Debonaire spin driers. If so perhaps you could give me a ring with a sort of price you might have on them.”
I just don’t quite know how to ring him back without bursting out laughing.
Maybe 💡 he got me mixed up with Goatboy
Mike.Re: zanussi wjd 1667
Sounds like it might have been accidentally put into some sort of diagnostics mode.
Mike.Re: oxy’balls
kwatt wrote:
Did I miss something or not answer any of this?
K.
No, you answered everything.
I just didn’t want anyone going away under the misapprehension that I was a believer in miracles.
Mike.Re: oxy’balls
Penguin45 wrote:you don’t hang your clothes on the washing line and throw stones at them, do you?
Chris.
Could be worth a try. Keep the kids away from worse mischief at half term. 😆
Mike.Re: oxy’balls
Just as I thought. That’s why I suggested you went back and read my first post in this thread. I hope that you have now understood that you surmised wrongly.
Mike.
