Forum Replies Created
-
Posts
-
Re: Why is it…………
aqualectric wrote:so it’s been “guess the fuel level” this week. :rolls: Better get that bike fixed Mike; I might have to borrow it at this rate. 😆
Steve.
What’s wrong with the guage stick? 😆
You can borrow my spare bike if you pop in to the bike shop on the way out of town and pay them their fiver to true up the back wheel. 😀
Mike.Re: Whitegoods v’s Osama Bin Laden?
chezza wrote:
Martin wrote:
2) He has offered to subject his body and soul to whatever International judgement is metered upon him?
would this be the standard insulation tester ? or something more complicated ? 😆 😆
Maybe the loopy tester? 🙂
Mike.Re: Blomberg 1501AAA washing machine spider
OK, I gave up after trying to phone Turkey and getting the answerphone in Turkish and having both e-mail addresses bounce back. 😥
Mike.Re: Samsung RL33SBNS
Mediator shows PDFs of this one. But I can’t see quite what you’re after.
Is it the part number 3 in the freezer section?
Mike.Re: Why is it…………
Snap! Two punctures in a week! Think it’s worse when the roads are wet; the bramble thorns don’t blow away in the wind.
Mike.Re: whirlpool hdw1011wg
Could be more clogging up at the in-line tap especially if it’s one of those self plumb fittings which only tap a small hole in the pipe. The fact that the filter was clogged up after only two years shows the supply is not too clean.
Mike.Re: Smeg oven hinges – Model F1100msx5
Maybe an enquiry to this site might turn up something?
Mike.Re: Smeg oven hinges – Model F1100msx5
It (well nearly) does exist! Maybe she got it in Espana?
S1100msx5
Always ask “Is that f for Freddie?”
Doesn’t get you any closer to the hinges though, sorry 🙁 .
Probably would need to see old ones and compare with pics on Connect or e-spares etc.
Mike.Re: Indesit w123
There are so many possible causes of this fault. I find it best to get a board from EMW after doing ten minutes of checking of the obvious. (Blow into p/sw, blow down p/sw tubing to check not blocked, quick check ntc resistance (25k ish at room temp IIRC), ntc connector, htr continuity, motor plug tight and pull on wires to see none are loose, check armature clean, i.e. brushes not down, filter not blocked, alright twenty minutes, remove module and mark connections with felt pen so you get it back right, examine closely for burns/ dry joints, alright thirty minutes 👿 )
Determine from emw site info which module req, ring up and get one sent out, miss postie and have to collect from sorting office, return to job and refit. Pray like mad and switch on (after doing all safety checks 😉 ).
90{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} work, 10{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} you’ve still got F8 👿 👿 and there is absolutely no way to crack it 😡 😡 . Oh and before you even begin you have to persuade the customer that it’s worth trying to fix it and it’s gonna cost quite a bit .
Actually these days I spend ten to twenty minutes on the phone when a job like this pops up explaining the difficulies involved and then having to explain why a) I don’t sell re-cons b) about how it’s a minefield out there choosing your new machine and why I can only give a list of what to avoid, probably.
Mike.Re: meggers
Martin wrote:Why didn’t it trip the RCD I hear you cry? For those that know the answer then time to rest on your laurels, turn away and take the rest of the day off!:D
Thanks for that. 😀 Shame there’s only an hour and a half left. 🙁 I wish I knew why the clock on this post says it’s only half an hour but that doesn’t really matter. Would I be correct in thinking that the trip would only blow if the insulation res. went down to about 8k?
Mike.Re: made to measure element
Re: Ikea whirlpool 10066613 oven
Think your best bet, if no answer forthcoming from the site, is to get the old one out and compare it with pics and dimensions given on this site;
http://www.elementreplacement.co.uk/gri … ts-2-c.asp
Mike.
